3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts, Compute for the tensile stress (MPa) in the plate at the critical section. Select the correct response: 28.57 18.18 15.38 19.23

3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts, Compute for the tensile stress (MPa) in the plate at the critical section. Select the correct response: 28.57 18.18 15.38 19.23

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

Q: Question 16 of 20 3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the…

A: given data diameter=20mmthickness=25mmWidth = 130mmload = 50KN

Q: es Required information Problem 01.061- A two link assembly with point loads Two horizontal 13-kip…

Q: The following structure has pin reactions are given.

Q: 10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80…

A: Given, P =80 kN diameter of bolts = 10mm thickness of plate(t)=8mm, width of plate (b)=300 mm

Q: Q4. A single strap single riveted butt joint joins two plates (12 mm and 10 mm), when the diameter…

A: Given: Plate thickness = 12 mm and 10 mm diameter of rivet = 14 mm c/c of adjacent rivets = 60 mm…

Q: B. What force is required to punch a square hole shear strength is 350 MNm2. (25-mm 25mm) in a plate…

A: The punching force can be found out by using following relationship: Force (F)=Hole…

Q: A staggered bolted connection has bolts arranged as shown. Diameter of bolts is 19 mm. Fy = 248 MPa.…

Q: For the connection shown, the bolt diameter is d = 15 mm. The average shear stress in the bolts must…

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

A: Force = 22.3 kN or 22300 NDiameter of shank, d = 12 mm Thickness (t) = 8mm

Q: Considering the dimensions given in the figure below, the specified application point of the plate…

A: The maximum shear stress will be experienced by the bolt B because it is at the maximum distance…

Q: The five-bolt connection shown must support an applied load of P = 400 N. The thickness of the axial…

A: P = 400 kN t = 1 mm b = 16 mm

Q: 174069&message_id%3Dmid.%24CAAAA Question 3 For the truss shown, determine the forces in members (a)…

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

Q: Problem 8.4 Distributed Loads The framing system shown in the figure is subjected to a 7.7 kN point…

Q: 4. The structure shown is hinged at A and C. Find the horizontal and vertical components of the pin…

Q: 3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile…

Q: 5. what is the shear rupture capacity of the shear plate of the shear connection in kips? (2 decimal…

A: a)Thickness of shear plate= 0.5 inA992: Fy = 50 ksi, Fu = 65 ksiA36: Fy = 36 ksi, Fu = 58…

Q: 4. Six rivets are used in the connection shown in the figure. If both P = 50 kN, what is the minimum…

A: Load P = 50KN Allowable shear stress = 70MPa Bearing stress = 40MPa

Q: Determine the bolt diameter if the shear stress is 150 MPa and the bearing stress is 337.50 MPa.

A: The values and diagram given in the question are as follows: Shear stress(t)=150 MPa Bearing…

Q: Determine the adequacy of the clip angle connection shown. The allowable stresses are 100mpa for…

A: Given data :- Allowable stress is 100 mpa for shearing and 220 mpa for bearing and 140 mpa for…

Q: "l zain IQ A:0 I YA docs.google.com/forms O 0/10 find the tensile stress in upper plate in section…

A: Given, P = 80kN Dia if bolt = 10mm Dia of hole = 10 +1 = 11mm No. Of bolts at section 1- 1 = 3,

Q: How many (answer should be a whole number) 22-mm diameter rivets are required to fasten member BC to…

Q: 10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80…

Q: SITUATION II: Calculate the permissible tensile load P 50 under the following conditions: Fy3248…

Q: Figure P-130 shows a roof truss and the detail of the riveted connection at joint B. Using allowable…

Q: The butt joint shown in the figure is connected using şive 20 mm diametor bolt. Ip the tension force…

A: Given data, Tension force(P)= 25 kN Diameter of bolt=20 mm number of shear plane=2 number of bolt=2…

Q: Calculate the strass In each mamber and identify what the factor of safely to failure 13? 19

A: Given:- Cross section of the members is 3" x 10" To find:- Stress in each members Concept:- Method…

Q: A flanged bolt coupling consists of six 12-mm-diameter steel bolts (Gst = 80 GPa) on a bolt circle…

Q: D 30 kN 70 kN 2 m 12 mm-thick gusset plate 10 -mm-thick 2 m angle 1.5 m-15 m- 15 m--15 m 8 mm-thick…

Q: 10/10 find the shear stress in bolt in pin A 60 kN 4 M 3 BOLT DIA 20 MM A 50 kN PIN A 636 MPa O 159…

Q: On the above figure, determine the following: 1. Maximum bearing stress at joints ( bolts and…

A: The given data is: The force is given=SN KN 1. The maximum bearing stress at joint:…

Q: REVISED PROBLEM: M3 HW 4 4. Six rivets are used in the connection shown in the figure. If both P =…

Q: Find the Zero- Force Members at the shape: D. 10 A M 10 ft 10 t 10 A 10 A 10 ft 10 t 10 A 6 kips 6…

A: To find the zero force members-

Q: BOLTED CONNECTIONS For the figure shown, use P = 100 kN, L = 300mm, SI = 100 mm and S2 = 180 mm.…

Q: Example: The five-bolt connection shown in Fig.1 must support an applied load of P=300kN. If the…

Q: Answer fast and send right answer

Q: 2. A butt joint is fastened by four %4" diameter bolts. If the joint transfers a tensile force P of…

A: Objective: To compute the average shearing stress in the bolts and the bearing stress between the…

Q: For the connection shown, determine : a) Sigma (stress) on the plate, if N = -6 kN (negative sign…

A: Given:- Thickness of plate, t = 10 mm Width of plate, w = 2R = 2 x 30 = 60 mm Diameter of pin, d =…

Q: An electrical resistance strain rosette indicates strains of -400, +800 and +500 along the x, y and…

A: Given- Strain rosette strains -400, +800, & +500, It is needed to find the value of the shearing…

Concept explainers

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.

Question

CT JO 7 IC
3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts,
Compute for the tensile stress (MPa) in the plate at the critical section.
Select the correct response:
28.57
18.18
15.38
19.23

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

BOLTED/RIVETED CONNECTION: SITUATION: In the figure, assume that a 20-mm-diameter rivet joins the plates that are each 110 mm wide. The allowable stresses are 120 MPa for 20-mm Ø VE P bearing in the plate material and 60 MPa for shearing of rivet. 1. Determine the minimum thickness of each plate 2. Determine the largest average tensile stress in the plates if the rivet hole is 2mm larger than the rivet diameter. O 110 mm
Hand written and clean writing
The five-bolt connection shown must support an applied load of P = 371 kN. If the average shear stress in the bolts must be limited to 174 MPa, determine the minimum bolt diameter that may be used in the connection. Answer: d = i mm.
2. For the figure shown below, determine the following; (60 points) a. Maximum tensile stress b. Maximum compressive stress c. Spacing/pitch of the bolts if the shear force resisted by each bolt is 30 kN 200 mm 100 mm 30 kN/m 10 mm 20 mm |100 kN 15 kN/m 5 kN-m 150 mm C D F 20 mm 3 m 0.5 m 0.5 m 1 m 3 m 20 mm 125 mm
Draw simple FBD and submit the solution within 25 minutes, Urgent.
The five-bolt connection shown must support an applied load of P = 300 N. The thickness of the axial member: = 1.5 mm. and the width = 18 mm If the ultimate shear stress in the bolts must be limited to 265 MPa with F.O.S = 3.7 . And the ultimate normal stress in the axial member = 250 MPa, with F.O.S = 2.8 , And the ultimate bearing stress in the axial member = 110 MPa, F.O.S = 2.5 Determine the minimum bolt diameter that may be used in the connection
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Please help with the problem below
show the complete solution
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
3-20 mm diameter bolts fasten two plates being 25 mm thick and 130 mm wide. If the applied tensile load is 50 kN is distributed uniformly among the bolts, Determine the shearing stress (MPa) in each rivet Select the correct response 53.05 17.68 10.61 159.15
00" zain IQ docs.google.com/forms O no one 10/ find the bearing stress between bolts and plate 5 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 125 MPa 12.5 MPa 250 MPa no one O 5/5 find the normal stress at left of int D + ...