Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The angle is ASTM A36 steel.

Q: The figure shows a roof truss and the detail of connection at joint I. The allowable stresses are 70…

A:

Q: Determine the nominal axial compressive strength of the members shown in the following figure. 1.…

A:

Q: The figure shows a roof truss and the detail of connection at joint B. The allowable stresses are 70…

A:

Q: What is the reference positive bending stress, F*bx, of a glulam member from the 20F-1.5E stress…

A:

Q: A welded tension member is consisting of two channels placed 400mm back to back with flanges turned…

A:

Q: 10/10 find the tensile stress in upper plate in section 3-3 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80…

A: Given, P =80 kN diameter of bolts = 10mm thickness of plate(t)=8mm, width of plate (b)=300 mm

Q: A W18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 23 kips,…

A:

Q: Part 2: Identify the read forces 4m 1) 60⁰ 4m 4m 10KN Rea'd: All member forces (use metheel of…

A: Given data in question  Load 10 kN Span member length   4m Angle 60° To find out  Member forces

Q: The wall bracket show below carries a load of P Kip. the allowable tensile in the eye bar is 20 ksi,…

A: According to question :

Q: AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 27 kips, w…

A: Given:- A W18×40 standard steel shape beam is used to support load The magnitude of the point load =…

Q: The five-bolt connection shown must support an applied load of P = 400 N. The thickness of the axial…

A: P = 400 kN t = 1 mm b = 16 mm

Q: For the given loaded truss, the allowable tensile stress in any member is up to 800 MPa while the…

A:

Q: A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield…

A:

Q: Part 2: Identify the read forces 4m 1) 60⁰ 4m 4m 10KN Rea'd: All member forces (use metheel of…

A: Given data  Find all member force using method of joint.

Q: Find out the strength and efficiency of a bolted lap joint .The bolts are of 30mm diameter, grade…

A: Diameter of bolt, d= 30 mmDiameter of bolt hole, do=30+2.5=32.5 mmFor bolts of grade 4.6 fub =400…

Q: Determine the no. of rivets to fasten the member BD

A: GIVEN: 1. Rivet strengths at working conditions : In Shear = 70 MPa In Bearing = 140 MPa 2.…

Q: Problem No. 1: 200 kN A truss joint is shown in the figure. 2-1. 100x100x12 H (a) Determine the…

A: Given:- A truss joint is shown The magnitude of the load = P = 200 kN The diameter of the bolt is 16…

Q: Problem 3: Six 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the average…

A:

Q: steel section. Check web yielding and web crippling if the steel used is ASTM A992, grade 50.

A: Solution: For W18×50, we obtain the following properties from ASTM, Below are the structural steel…

Q: dentiry the shown. (Enter your separated E A

A:

Q: he bolt is made of a material havin llowable shearing stress of 55.44 M

A: Given:- Allowable tensile stress=140.44MPa Allowable shearing stress=55.44MPa Axial load=17kN…

Q: Determine the force in each member of the truss shown. Indicate whether the members are in tension…

A:

Q: choose the W section of 50 ksi steel

A:

Q: Determine the maximum i tensile and compressive stress for the beam with the given cross section.…

A:

Q: How many (answer should be a whole number) 22-mm diameter rivets are required to fasten member BC to…

A:

Q: PROBLEM 1: CHECK THE ADEQUACY OF MEMBER BC WHOSE THICKNESS IS 14 mm, FIGURE : to

A:

Q: The figure shows a roof truss and the detail of the connection at joint D. Member DE is angle…

A:

Q: Calculate the strass In each mamber and identify what the factor of safely to failure 13? 19

A: Given:- Cross section of the members is 3" x 10" To find:- Stress in each members Concept:- Method…

Q: Plate 10 4 in. Plate x8 <8

A:

Q: For the welded tension member shown in the figure,determine the shear lag factor, U; the net area,…

A:

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.