Determine the allowable (ASD) tensile strength (kN) of the angle shown. It is welded on the end (transverse) and sides (longitudinal) of the long leg only. The yield strength is 248 MPa while the ultimate tensile strength is 400 MPa. Neglect block shear strength. The angle is L203X152X19. Plate weld Angle Section view Plate 120 →→→→Plan view 150 203

Determine the allowable (ASD) tensile strength (kN) of the angle shown. It is welded on the end (transverse) and sides (longitudinal) of the long leg only. The yield strength is 248 MPa while the ultimate tensile strength is 400 MPa. Neglect block shear strength. The angle is L203X152X19. Plate weld Angle Section view Plate 120 →→→→Plan view 150 203

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

X= 482 show complete solutions and FBD
Hand written plzz This is the corresponding tensile stress (MPa) at the minimum strain (as allowed by NSCP2015) of extreme tension steel. Assume f'c-28 MPa and fy-420MPa
A tension plate shown below is used to support suspended load "T". Gusset Plate- F, = 248 MPa Fu = 400 MPa %3D 200 mm a) Determine the allowable tensile capacity of the plate if L= 240 mm. (Assume weld strength is satisfactory).
What will be the tensile strength due to rupture of critical section of an angle section ISA 150 × 115 x 8, which is connected to gusset plate as shown in figure?. Use Fe410 grade steel. 150 mm 115 mm 8 mm 8 mm 60 mm 150 mm
Centroid + Inertia 200 x 20 mm Plate The strength of the rolled section shown is increased by combining S section, channel, plate and then welded. 1. Determine the location of its centroid; and 5310 x 47.3 C310 x 30.8 2. Determine the moments of inertia of the composite section with respect to its centroidal x and y Semi-circle Weld, 10mm radius axes.
b. The gusset plate shown in Figure 10 is welded to a vertical member. The gusset plate carries a load of 250 kN acting at a distance of 250 mm from the closest edge of the weld. The weld around the gusset plate is completed in two 140 mm horizontal portions and one 320 mm vertical portion. If the maximum allowable shear stress of the weld is 200 N/mm², detemine the minimum thickness of the weld required. In calculations, the second and higher order terms of the weld thickness for second moment of area calculations may be neglected. 250 kN 140 mm 250mm 140 mm Figure 10 320 mm
Y1
rectanqular seetion with width bz250 and depth h= 500mm is to carcry a A m %3D design bending moment M= 260KN•M, The conerete is of greade e30 and the tensile steel is of HRB400. The tension reinforzce. ment A, is requined.
Determine the length of tension anchorage required for the 36 mm diameter plain mild steel reinforcing bars in the canrilever of figuer below. The charactersitic material strengths are feu-30N/mm² and fy=250KN. The ultimate anchorage bond stress. Stress, fou-1.5N/mm² Anchorage length R25 bars
PC =? PI=12+00.00 T = ? E = ? L = ? Tangent, T = Degree, Da= Length, L = Long Chord, LC = MO = ? LC = ? R = 5730 ft I = 1°00'00" PT=? Questions 29-34: Calculate the remaining parts of the circular curve given above: External, E = Middle Ordinate, MO =
Please help me with my homework and use ASEP STEEL HANDBOOK 2004 volume 1 Dimensions and Properties Third Edition, to find the AISC. PLEASE SHOW COMPLETE SOLUTIONS AND DETAILS.
PLEASE ANSWER THIS QUESTION ASAP!!!