PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a diameter of 12 mm and an allowable shear stress of 80 MPa. Each plate has an allowable tensile stress of 60 MPa, an allowable bearing stress of 70 MPa, and an allowable shear stress of 30 MPa. Answer: P = 25 kips (controls) P/2 P/2 30 mm- 15 mm P 30 mm

PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a diameter of 12 mm and an allowable shear stress of 80 MPa. Each plate has an allowable tensile stress of 60 MPa, an allowable bearing stress of 70 MPa, and an allowable shear stress of 30 MPa. Answer: P = 25 kips (controls) P/2 P/2 30 mm- 15 mm P 30 mm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.12.2P

See similar textbooks

Similar questions

Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
Two bolts are used to lap points two steel plates. Tensile force on the plate is 45kN. Determine the required diameter of the bolts if the failure shear stress of the bolts is 350 MPa. Use a factor of safety for shear equal to 2.0
A plate with width of 420 mm and thickness of 13 mm is to be connected to a plate of the same width and thickness by 30 mm diameter bolts, as shown in the Figure 1. The holes are 3mm larger than the bolt diameter. The plate is A36 steel with yield strength Fy = 248MPa. Assume allowable tensile stress on net area is 0.60Fy. It is required to determine the value of b such that the net width along bolts 1-2-3-4 is equl to the net width along bolts 1-2-4. W = 420 mm t = 13 mm a = 64 mm c = 104 mm d = 195 mm Bolt Diameter = 30 mm Holes Diameter = 30 mm + 3 = 33 mm ?? = 248 MPa Allowable Tensile Stress on ?? = 0.60Fy a. Calculate the vaue of b in millimeters. b. Calculate the value of the net area for tension in plates in square millimeters. c. Calculate the value of P so that the allowable tensile stress on net area will not be exceeded.
Determine the design tensile strength of the 12 in. x 1/2 in. steel plate shown in the figure. The bolts are 3/4 in. diameter. The steel is A572 Gr. 50. Check yielding and fracture. Check Block Shear. T 3in. 73im 13in 1 3in t
Kindly do not copy the solution from outside. Quick and correct answer required.
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm
A single unequal angle 100 x 75 x 6 is connected to a 10 mm thick gusset plate at the ends with six 16 mm diameter bolts to the 100 mm of leg to transfer tension as shown in figure. What will be the block shear strength (in kN) of the angle section assuming that the yield and the ultimate stress of steel used are 250 MPa and 410 MPa respectively? ISA (100 × 75 x 6) -T 16 mm o bolt 10 mm 40 mm 40 mm| 40 mm 40 mm 40 mm 40 mm 10 mm
The following image shows a front and side view of the column connection. The bolts have a diameter of ¾”. The W12X65 profile has a thickness of 0.605”. Determine:a. The shear stress in the bolts.b. The axial stress in the bolts.c. The support stress in the W12X65 profile.
Situation 2. Two plates each with thicknessF16mm are bolted together with6 -22mm dimater bolts forming a lap conne ction. Bolt spacing are as follows: S1 = 40mm, S2 = 80mm, Sa = 100mm. Bolt hole diameter=25 mm 50 250mm 30 30 60 75 Allowable stress: Tensile stess on gross area of the plate=0.60 Fy Tensile stress on net area of the plate=0.5Fy Shear Stress of the bolt Fv=120MPA Bearing Stress of the bot Fp=1.2 Fu Calculate the permiss ible tensile load P under the following Conditions: 4. Based on shear capacity of bolts 5. Based on bearing capacity of bolts 6. Based on block shear strength (taking into consideration the failure path given in the figure below) 40 80 16 mm 40 180 mm 40 Bearing Failure Path #1 140 209 Bearing Failure Path #2
For the clevis connection shown, determine the shear stress in the 23-mm-diameter bolt for an applied load of P = 165 kN. O 141 MPa O 211 MPa O 167 MPa O 120 MPa O 199 MPa Clevis
Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1 = 50, y2 = y3 = y4 = 100 y1 y2 y3 y4 O 80 MPa O 71 MPa O 74 MPa oooo O 86 MPa O 1. Which of the following nearly gives the shearing stress of the most stress bolt? Use 20 mm diameter bolt. x1 O O O x2
Prepare an excel file and to find a) area of the bolt, b) Average Shear Stress Bolt c) Bearing Area Stress and d) allowable stress. Applied force range – 500 to 1000 N (in step of 100 N) Bolt diameter range – 10 to 25 mm (in step of 5 mm) Plate thickness – 10 mm Consider ultimate tensile strength as 460 N/mm2. And consider factor of safety as 1.5.