b) A column is connected by a double lap joint consists of 10 mm thick grade S275 plates. All edges of the plates are machine flame cut. Four (4) 20 mm diameter Grade 8.8 black pre-stressed fully threaded bolts are used. The column is loaded with a 400 kN axial load. The surface of plates is blasted with grit, and painted with alkali-zinc silicate paint. Given: e₁ = 50 mm e2 = 25 mm P₁ = 200 mm P2 = 50 mm ii) Calculate the slip resistance and tensile resistance of the plates for the double lap joint.

b) A column is connected by a double lap joint consists of 10 mm thick grade S275 plates. All edges of the plates are machine flame cut. Four (4) 20 mm diameter Grade 8.8 black pre-stressed fully threaded bolts are used. The column is loaded with a 400 kN axial load. The surface of plates is blasted with grit, and painted with alkali-zinc silicate paint. Given: e₁ = 50 mm e2 = 25 mm P₁ = 200 mm P2 = 50 mm ii) Calculate the slip resistance and tensile resistance of the plates for the double lap joint.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is connected to a gusset plate using welds 12 inches long, as shown in the figure. The service live load is three times the dead load. Use A992 steel. USE LRFD ONLY, no block shear will occur. What is the Maximum Tensile SERVICE Load Round your answer to 3 decimal places.
Compute the service load capacity P for the welded bracket of the accompanying figure. The load is 70% live load and 30% dead load. Neglect the returns at the outer ends of the C-shaped weld configuration. The weld size is 3/8" (9.53 mm) and E70 electrodes are used in the shielded metal arc process. • Use strength analysis ● Use elastic method 203.50 -12.70 THK -285.75 -63.50
i need the answer quickly
1. Determine the required weld size necessary to carry the load P. PDL = 360 kN and PLL= 120 kN. Use E60 electrodes and LRFD. P. 130 E60 200 200 200 E60 150
b) Figure Q1(b) shows a glued connection between 3 metal plates. The plates are 500 mm wide. The glue has a shear capacity of 30 MPa. i. Determine the glue length L if the value P = 80 kN. ii. If the glue is to be replaced by 12 mm diameter bolts with shear strength of 180 MPa, determine the number of bolts required. P. 500mm P/2 P/2 FIGURE Q1(b)
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 16 ksi. O 480 psi O 305 psi O 376 psi O 407 psi 523 psi
Need complete and elaborate solution A.Using ASD, check the adequacy of the base plate (PL400x350x19 mm) centered on a W12X152 column as shown. It is resting on a concrete pedestal that is 450 mm x 400 mm. The loads are PDL = 600kN and PLL = 320 kN. Use A-36 steel and concrete fc’=20 MPa. B. Using LRFD, PL400x350 mm base plate, W12x120 column, 500x500 mm pedestal, PDL = 1200 kN and PLL = 800 kN. Use A-50 steel and concrete fc’ = 30 MPa. Determine the required base plate thickness.
Q2: aluminum rod AB (G 27GPA) brass rod BD (G = 39GPA). portion CD of the brass rod is hollow and has an inner diameter of 40 mm, Determine: a) the angle of twist at A. b) maximum shear stress of rod AD c) torque diagram d) angle of twist diagram
Design a double angle tension member that is fillet welded to a gusset plate. Assume that the angles will be made from A36 steel, and the gusset plate from A572 Gr. 50 steel. Use 70ksi electrode. Design the system to resist a factored load of 200 kips. Check all applicable limit states that are possible. Provide your results on a sketch with standard weld symbols and details.
A double angle ISA 75mm x 75mm x 8mm back- to-back welded to one side of a 12mm gussethave allowable stress 150MPa. Determine the allowable tensile load on the members and weldlength and overlap length of gusset plate.
The bolt is made of a material having an allowable tensile stress of 140.44 MPa and an allowable shearing stress of 55.44 MPa. The bolt will be tightened so that the axial load will be 17 KN. Find the required thickness of the bolt head if the thread is 0.25 mm deep.
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in