Draw moisture density curve and determine the ddman-CALIBRATION OF MOLD:Weight of Mold = 4.30kgHeight of Mold=11.6cmDiameter of Mold=10.16cmTRIAL WEIGHT OF MOLD +MOIST SOILDRY SOILWEIGHTSOIL SAMPLE, kgSAMPLE + CAN, gSAMPLE + CAN, gOF CAN, g5.5232.6032.0016.0725.7434.6432.7516.315.9536.6533.1616.1245.9236.1131.3116.4155.6848.9639.9516.573.1.

Bulk Density = (Weight of Mold + Soil Sample)-Weight of MoldVolume of Mold Moisture Content (w)…

Draw moisture density curve and determine the ddman. CALIBRATION OF MOLD: Weight of Mold = 4.30kg Height of Mold=11.6cm Diameter of Mold=10.16cm TRIAL WEIGHT OF MOLD + SOIL SAMPLE, kg MOIST SOIL DRY SOIL WEIGHT SAMPLE + CAN, g SAMPLE + CAN, g OF CAN, g 1 5.52 32.60 32.00 16.07 5.74 34.64 32.75 16.31 3 5.95 36.65 33.16 16.12 5.92 36.11 31.31 16.41 5 5.68 48.96 39.95 16.57 2.

Draw moisture density curve and determine the ddman. CALIBRATION OF MOLD: Weight of Mold = 4.30kg Height of Mold=11.6cm Diameter of Mold=10.16cm TRIAL WEIGHT OF MOLD + SOIL SAMPLE, kg MOIST SOIL DRY SOIL WEIGHT SAMPLE + CAN, g SAMPLE + CAN, g OF CAN, g 1 5.52 32.60 32.00 16.07 5.74 34.64 32.75 16.31 3 5.95 36.65 33.16 16.12 5.92 36.11 31.31 16.41 5 5.68 48.96 39.95 16.57 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the following: a.) %F2,F3,F4,F5,F6,F7,F8 Assuming that D60 = 0.297; D30 = 0.172; D10 = 0.151 b.) calculate Cu and Cc
Q/An experiment was made to find the specific gravity of soil in the laboratory and the results were below. What is required is to make a discussion of the results Specimen number 1 S16.4 616-4 Pycnometer bot lle number Mass ol Pycnometor, wn (g) Mass of Pycnometer and dry specimen, wpes (9) Mass ol Pycnometer, specimen and waler, w,w (9) 679,4 Moss ol Pycnometer and water, Wpew (g) 635,2 Specific gravity. G; Average Specilic gravily. G,
Soil placed on a can has been weighed before and after an oven-drying procedure. The procedure yeields the following results: Mass of soil + can before placing in the oven (82.2g) Mass of soil + can after placing in the oven (73g) Mass of can (34.5g) If the specific gravity of the soil is 2.78, and the void ratio is 0.636, what will be the moist unit weight (kn/m3) of the soil? Use stored value. Answer to 5 decimal places.
What is dry unit weight of the soil sample below (y) in lb/ft3 ? The combined weight of a mold and the compacted soil sample is 8.7 lb The mold's volume is 1/30 ft The mold's weight is 5 lb The soil samnple's water content is 13% Please ROUND to the nearest Thousandth (i.e., 0.001). Enter only numbers (Do not enter units!) Answer:
Question 8 A cylindrical specimen of a cohesive soil of 11 cm diameter and 22 cm length was prepared by compaction in a mold. If the wet mass of the specimen was 3.14 kg. and its water content was 17.01%. (Specific gravity of soil solids is 2.74). Determine the void ratio of the soil. Round off to three decimal places.
The results of a standard Proctor test are given in the following table. Determine the maximum dry density (kg/m3) of compaction and the optimum moisture content
-
The following are the results from the liquid limit and plastic limit test for a sail Liquid limit = 39.1% Plastic limit=18.7% a. b. C. No. of Blows 15 20 28 LI Moisture Content 42 40.8 39.1 What is the plasticity index of the soil? What is the liquidity index if the water content is 24%? What is the consistency index?
Plz, solve this problem as detail. Geotechnical Engineering-1
The dry weight of sample = 1kg. Result of sieve analysis are shown below. Sieve Size Weight retained (g) 4.65 mm 0 2.46 mm 100 1.98 mm 250 0.30 mm 350 0.10 mm. 200 0.5 mm 100 Determine the Fineness Modulus.
A Standard Proctor Test was completed according to Method A described in Chapter 12. The following laboratory data was obtained: Mass of mold = Mass of moist specimen and mold = Volume of compaction mold = Mass of container= 51.5g Mass of container plus moist soil= 261.85g Mass of container plus oven-dried soil= 231.83g 1.98 kg 3.718 kg 0.0009438m3 Determine the Dry density of compacted specimen. (expressed in Mg/m3, 3 decimal places) Your Answer:
The laboratory test data for a standard Proctor test are given below. Volume of Mass of wet soil in the mold (kg) Moisture content Proctor mold (%) (ст3) 943.3 1.65 10 943.3 1.75 12 943.3 1.83 14 943.3 1.81 16 943.3 1.76 18 943.3 1.70 20 a) Find the maximum dry unit weight and optimum moisture content. b) Calculate the zero-air-void unit weights for a soil with G, =2.68 at moisture content of 5, 10, 15, 20, and 25%. Plot a graph of Yzav versus moisture content.