I tried this problem but I can't seem to figure out what I am missing here can you please help me? Determine the average normal stress at point A.The diameter of each segment is indicated in (Figure 1). Take P₁ = 1 kip, P₂ = 6 kip,P3 = 9 kip, and P₁ = 4 kip.Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension.ΜΕ ΑΣΦ↓↑ vecσA= 7.5?ksiFigure0.5 in.P₁AP21 in.0.5 in.SubmitPrevious Answers Request Answer× Incorrect; Try Again; One attempt remainingPart BDetermine the average normal stress at point B.Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension.?Η ΜΕ ΑΣΦVAΣ+It vec1 of 1OB = 5Submit Previous Answers Request Answer× Incorrect; Try Again; 4 attempts remainingP₁ CP4Part CksiDetermine the average normal stress at point C.Express your answer in kilopounds per square inch to three significant figures. Enter negative value in the case of compression and positive value in the case of tension.

Answered: Determine the average normal stress at…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

= Consider a hollow circular shaft of inner radius r; = 1.25 inch and outer radius of ro 1.50in, subjected to the following loads Fx = 100 lb, Fy = 150 lb, and F = 100 lb. Determine the state of stress (3x3 matrix) and the principal stresses at point p. Report your answers in psi to one decimal place. Note the figure is not to scale. у P fixed support R1-25 in 90⁰ X 90⁰ R2=50 in h=20 in Fy Note the hollow circular shaft lies in the x-y plane only Fz Fx ro ri || = /1.50" 1.25" YZ cross-section р X
An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN force has been applied, the separation between the lines has increased to l' = 10.009 cm. 30 cm 10 cm -F l' a. Calculate the stress and strain in the rod. (Express your answer for stress using two significant figures.) |MPa (Express your answer for strain using four decimal spaces.) E = b. To what total length has the rod stretched? (Express your answer using three decimal places.) L final cm
correct ans
Determine the equivalent state of stress if an element is oriented 20° clockwise from the element shown in Figure 1. σχ, σγ' and τχγ 2 MPa 3 МРа 4 MPa
Calculate the stress in the steel from the given figure. Use P1=300 kN and P2=45 kN. Answer in MPa
The state of stress at a point in a member is shown on the element. Determine the shear stress component T'xy (in ksi) acting on the inclined plane AB. Use Excel spreadsheet posted on Canvas and give correct answer to one decimal place. σx = 4.6 ksi đy = 3 ksi Txy = 10.7 ksi 0 = 40° A xy B 40° x
A plane stress state is given by the principal stresses σx =25 MPa and σy= -11 MPa. Determine σx' in the case that the system is inclined by 30 degrees (counter-clockwise). Give your answer in MPa to the nearest whole number.
The state of plane stress at a point is represented on the element shown in the figure below. (a) Determine the principal stresses acting on this point, and the corresponding orientation (angle). (b) Determine the maximum in-plane shear stress, and the corresponding orientation (angle). Also determine the associated average normal stress. Draw Mohr's circle and show the stresses on the circle. 16 MPa 10 MPа
Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure.
The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the original orientation where point A corresponds to the x face and point B corresponds to the y face. a) Show the stresses represented by line AB on the provided stress element. 60 X -30-1 {MPa} y T(MPa) b) Determine the principal stresses and show them on a properly oriented stress A element. y X 40 B 20p 30 40 40
Suppose that σ = 330 psi and Try = 150 psi in (Figure 1). Figure Part D Specify the orientation of the principal stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. Op₁= Part E OF 0₂ = ΑΣΦΙΚΗ vec Specify the orientation of the maximum in-plane shear stress. Take the positive direction of rotation counterclockwise. Express your answer in degrees to three significant figures. 0/ —| ΑΣΦ 11 | vec ? ? o
A steel bolt has a diameter of 8 mm. The bolt is encased by a bronze tube that has an outer diameter of 15 mm and inner diameter of 8 mm. A force is applied to the bolt. F d3 d1 F Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value F₁ 25 kN Esteel 200 GPa Ebronze 105 GPa a. Determine the magnitude of the normal force in the steel bolt, Nsteel. b. Determine the magnitude of the normal force in the bronze tube, Nbronze. c. Determine the magnitude of the normal stress in the steel bolt, σsteel. d. Determine the magnitude of the normal stress in the bronze tube, σbronze Round your final answers to 3 significant digits. Nsteel = KN Nbronze = KN σ steel = MPa MPa Obronze

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS