At a point on the surface of a pressurized cylinder, the material element is subjected to stresses; σx = 60 MPa, σy = - 40 MPa, and τxy = - 30 MPa. Construct Mohr’s circle, then use it to determine the following: Do not use the equations of transformations. 1- The principal stresses and the maximum shear stress. 2- Show these stresses on sketches of properly stress elements. 3- A point on the circle where the element is only subjected to pure shear stress. Calculate the value of that pure shear stress.

Q: The element of material below is subjected to the state of stress shown, where a = 120.0 MPa, b =…

A:

Q: For a point under a plane state of stress, the stresses on the vertical and horizontal planes are…

A: Find the normal stress at inclined surface. And location of principal plane.

Q: The state of stress in a material is given in the figure. Maximum principal stress will be 45 45 5 5…

A: Given, Tensile stress in x-direction = σx = 5 units Tensile stress in y-direction = σy = 5 units…

Q: A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa,…

A: We have given a stress element which consist a biaxial loading σx = 8 MPa in X direction, σy = 4 MPa…

Q: Q2 The state of stress at a point of an elastic solid is given in the x-yz coordinates by: (a)…

A: (a) Write the given matrix. σ=σxxσxyσxzσyxσyyσyzσzxσzyσzz=901800180240000120 MPa

Q: Determine the normal stress that acts at point B.

A: The rod diameter d =40 mm = 0.04m The force system Fx= 1390N Fy= 510N Fz= 835N Find a) The Normal…

Q: The drill shown is jammed in the wall and is subjected to the torque and force shown in the diagram.…

A: Given

Q: 60mm 2. H we measure a &=13µm decrease in the bolt diameter d. Bolt material properties are given as…

A:

Q: The Mohr's circle representing a given state of stress is shown. The diagonal line AB represents the…

A:

Q: At a point on a structural member subjected to plane stress, normal and shear stresses exist on…

A:

Q: The state of stress of an element is shown in the Figure 3. Using the method of Mohr's circle.…

A:

Q: The stresses shown below act on horizontal and vertical planes through a point on the surface of a…

A:

Q: [20 [o] = 10 0 b. Plot Mohr's circle for this stress state. 10 01 10 005 0 a. Determine the stress…

A: (a) Write the given stress matrix. σ=2010010100005

Q: In a thin plate, the state of stress prevails according to the figure. Calculate the principal…

A:

Q: Determine the equivalent state of stress if an element is oriented 60° clockwise from the element…

A:

Q: On a stress element, the following stresses are acting: σ x = 5 ksi (Compression) σ y =  10 ksi…

A:

Q: Ql: For the Figure shown below, determine (a) the principal stresses and show them on a sketch of a…

A:

Q: The following stress condition is applied on a material: 400 200 0 o 200-300 0 MPa 000 Determine the…

A:

Q: Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here,…

A:

Q: At a point in the cross-section of an engineering component an element is subject to the following…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A: Given:The stress in the x plane is the stress in the y plane is The shear stress in the x-y plane is…

Q: Using Mohr's circle, determine stress components on an element oriented 60 ° clockwise with respect…

A: Given σx=100 MPaσy=160 MPaτxy=60 MPa  As the element is oriented 60o counter clockwise we have the…

Q: For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to…

A: Explanation: To define the diameter of Mohr's circle, two points (σx,τ) and (σy,τ)  are required. By…

Q: Tyx Figure 1 Point A- x-direction stress 60MPA(compression), y-direction stress 40MPA(tension),…

A:

Q: QUESTION 5 For the stress element shown below, which 2 points (0, T) in the stress domain could be…

A: Find the two points to define the diameter of the mohr's circle

Q: Determine the principle stresses σ1, σ2, σ3 and their orientation φ, if σx, σy and σz are known as…

A:

Q: The distribution of stress in an isotropic aluminium machine component is given (in MPa) as: σ₂ = y…

A:

Q: The following Mohr's circle is for a point in a structural member that is subjected to plane stress.…

A: Given data:- Mohr circle of point To find:-The absolute maximum shear stress

Q: as depicted in the figure. As

A: given:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A:

Q: A state of stress at a point A is given by ox = 45 MPa, oy = 9.1 MPa, and txy = -5.75 MPa. What is…

A: The given values are - σx=45 MPa, σy=9.1 MPa, ζxy=5.75 MPaThe principle stress is given by -  σ1 ,…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: 15 mm 15 mm 200 mm 150 mm F 1 of 1 Determine the maximum and minimum normal stress in the bracket at…

A: F = 104 kN load applied at x= 0

Q: A body is subjected to the following stresses: og=10 MPa, oy -2 MPa, oz =3 MPa. Which of the…

A: For plane stress or 2D stress element they should two are normal stresses and one is shear stress.…

Q: Two non-parallel intersecting shafts are connected by a Hooke's joint. Driving shaft rotates…

A: A Hooke's joint is used to connect two non-parallel intersecting shafts.The driving shaft spins in a…

Q: in Fig. P2-89. U

A: given:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.