For the stress element shown below, which 2 points (σ, τ) in the stress domain could be used to define the diameter of the Mohr's Circle?         (- 80 MPa, - 25 MPa)     (50 MPa, 25 MPa)     (50 MPa, - 25 MPa)     (- 80 MPa, 25 MPa)

Q: The state of strain at the point has components of €, = 180(10 6) €y = -100(10-6) and All attempts…

A:

Q: If the 2-in. diameter supporting rods are made from A992 steel, determine the average normal stress…

A:

Q: Sketch Mohrt's circle for the following state of stress σx = 30 MPa, σy = -50 MPa and Txy = 45 MPa|…

A:

Q: ▾ Part B Determine the normal stress dy'. Express your answer to three significant figures and…

A:

Q: Why As is like 2(pi/4)d^2 This question asks for the average tension only in section a-a, is that…

A: As we can see that section a-a will be in shear and not in tension.

Q: On a stress element, the following stresses are acting: σ x = 5 ksi (Compression) σ y =  10 ksi…

A:

Q: Rod ABC has a diameter of 30 mm at AB and diameter of 20 mm at BC. the whole rod is subjected to a…

A:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 5)…

A: Given:The stress in the x plane is the stress in the y plane is The shear stress in the x-y plane is…

Q: QUESTION 5 For the stress element shown below, which 2 points (0, T) in the stress domain could be…

A: Find the two points to define the diameter of the mohr's circle

Q: The following Mohr's circle is for a point in a structural member that is subjected to plane stress.…

A: Given data:- Mohr circle of point To find:-The absolute maximum shear stress

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A:

Q: A body is subjected to the following stresses: og=10 MPa, oy -2 MPa, oz =3 MPa. Which of the…

A: For plane stress or 2D stress element they should two are normal stresses and one is shear stress.…

Q: he rod has a diameter of 40 mmmm. It is subjected to the force system Fx=1100 N, Fy=500 N, Fz=900 N.…

A: The forces are The diameter od rod is The torque is

Q: Bars (1) are made of steel [E = 30,000 ksi], and bar (2) is made of an aluminum alloy [E = 10,000…

A:

Q: Please work out c and d

A:

Q: A point on a thin plate is subjected to two successive states of stress. The stresses have magnitude…

A:

Q: The state of stress at a point in an elastic body is defined by the stress components, G11 = 2000;…

A: as per our company guidelines we are supposed to answer ?️only first 3 sub-parts. Kindly repost…

Q: An 6 mm diameter aluminum rod has lines scribed on it that are exactly 10 cm apart. After a 2.08 kN…

A: Given Data L=30 cm P=2.08 kN D=6 mm

Q: The rigid beam is supported by a pin at A and wires BD and CE. Figure 3 m 2m 1 of 1 4 m ▾ Part A If…

A: Given data  Downward displacement of C = 8mm Find the normal strain in CE and BD

Q: A rectangular column (blue color) is fixed to a rigid ground (brown color). As shown in the figure,…

A: aa

Q: n element is subject to the stresses shown below in Figure 5 Calculate the centre and radius of the…

A: Givenσx=75MPaσy=-30MPaτxy=14MPa

Q: The general stress element is loaded such that τxy = 25 MPa. Using Mohr’s circle, find out the…

A:

Stress transformation

The term stress indicates the measure of internal forces that develop due to an external force's application on an object. When a specific external force is applied to an object, internal stress generates in the material. The value of stress can obtain by taking the ratio of the externally applied force and cross-sectional area of the object. There are different types of stress depending on the type of external force.