Consider the hydraulic lift shown in the figure. The small piston has an area A₁ of 0.0330 m², and the large piston has an area A2 of 4.00 m². Assume that the fluid used in the lift is incompressible. What force F2 will the large piston provide if the small piston is pushed down with a force F₁ of 17.0 N? y₁ F₂ = A₁₂ Y2 F₂ 2 N If the small piston A₁ is slowly depressed a distance of y₁ = 0.400 m, what distance y2 will the large piston A₂ rise? y2 = m What is the magnitude W₁ of the work done when pushing down the small piston A₁? W₁ = J What is the magnitude W2 of the work done when pushing up the large piston A₂? W₂ =

Consider the hydraulic lift shown in the figure. The small piston has an area A₁ of 0.0330 m², and the large piston has an area A2 of 4.00 m². Assume that the fluid used in the lift is incompressible. What force F2 will the large piston provide if the small piston is pushed down with a force F₁ of 17.0 N? y₁ F₂ = A₁₂ Y2 F₂ 2 N If the small piston A₁ is slowly depressed a distance of y₁ = 0.400 m, what distance y2 will the large piston A₂ rise? y2 = m What is the magnitude W₁ of the work done when pushing down the small piston A₁? W₁ = J What is the magnitude W2 of the work done when pushing up the large piston A₂? W₂ =

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and the large piston has an area A, of 4.00 m?. What force F2 will the large piston provide if the small piston is pushed down with a force F, of 18.0 N? Assume that the fluid used in the lift is incompressible. F, = F, y2 A, A, F,
A hydraulic jack piston has a diameter of 0.06 m. The hydraulic jack is connected to another piston that supports the load. The support load piston has a diameter of 0.50 m. If the jack can lift a mass up to 2500 kg, what is the maximum force that one needs to apply to the piston in order to lift the given mass?
Solve
An open circuit containing five resistors starts at point a and ends at point b. The circuit extends to the right from point a and splits into two parallel horizontal branches. There is a 12.0 Ω resistor on the top branch and a 6.00 Ω resistor on the bottom branch. The branches then recombine and the circuit extends to the right to a 5.00 Ω resistor. To the right of the 5.00 Ω resistor, the circuit again splits into two parallel horizontal branches. There is a 4.00 Ω resistor on the top branch and an 8.00 Ω resistor on the bottom branch. The branches then recombine and the circuit extends to the right until it reaches point b. (b) If a voltage of 50 V is applied between points a and b, find the current in each resistor. 12 Ω ?A 6 Ω ?A 5 Ω ? A 4 Ω ? A 8 Ω ? A
In the hydraulic lift shown in the figure, A1 < A2. How does the pressure (P1) caused by F1 compare with the pressure (P2) caused by F2 in piston 2? Pa Jwrong O P1 = P2 O It depends on the weight of the car.
Two metal blocks are attached by a cable as shown in Figure P10.50 and are floating near the surface of a lake. If the volumes are V1 = 3 m3 and V2 = 1.23 m3 , what is the total buoyant force on the two blocks?
The small piston of a hydraulic lift (see figure below) has a radius of r1= 1.00 cm, and its large piston has a radius of r2=9.45 cm. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load of mass 1500 kg? Answer: N.
Consider the hydraulic lift shown in the figure. The small piston has an area A of 0.0330 m², and the large piston has an area A2 of 4.00 m2. What force F2 will the large piston provide if the small piston is pushed down with a force F of 17.0 N? Assume that the fluid used in the lift is incompressible. F2 %3D Y2 A, A, If the small piston A1 is slowly depressed a distance of yi = 0.200 m, what distance y2 will the large piston A2 rise? y2 = What is the magnitude W of the work done when pushing down the small piston A1? What is the magnitude W, of the work done when pushing up the large piston A2? W = J W2 =