A hydraulic jack has input piston with cross-sectional area 0.05 m2 and output piston with cross-sectional area 0.17 m2. If the input force is 640 N, calculate the output force in kN. kN (Note the units!)

A hydraulic jack has input piston with cross-sectional area 0.05 m2 and output piston with cross-sectional area 0.17 m2. If the input force is 640 N, calculate the output force in kN. kN (Note the units!)

Name: 6TOREA hydraulic jack has input piston with cross-sectionalarea 0.05
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: 6TOREA hydraulic jack has input piston with cross-sectionalarea 0.05 m2 and output piston with cross-sectional area0.17 m2. If the input force is 640 N, calculate the outputforce in kN.kN (Note the units!)直。SNSVf594E3f8f12E3OL因 ロ57.84.YK.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

The small piston of a hydraulic lift as shown in the figure has a cross-sectional of 3.00 x 10-4 m2 and its output plunger has a cross-sectional area of 2.00 x 10-2 m2 . The lift uses hydraulic oil that has a density of 8.50 x 102 kg/m3 . What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load (car and output plunger) whose weight is 1.50 x 104 N when the bottom surfaces of the piston and the plunger are at the levels with height difference of 1.5 m?
A booster pump on a brake system designed to be used horizontally consists of two cylinders capped by pistons connected by a hose. The cylinders and hose are filled with an incompressible fluid. The system produces a mechanical advantage of six times; that is, the output force is six times as great as the input force. If the cross-sectional area of the input piston is 2.6 in2, how large (in in2) must the area of the output piston be? _____________in2
A hydraulic lift is designed with an output cylinder that has 36 X the area of the input cylinder. If a force F is applied to the input cylinder, the output cylinder can supply a force equal to _______.
Consider the hydraulic lift shown in the figure. The small piston has an area Aj of 0.0330 m², and the large piston has an area A, of 4.00 m?. What force F2 will the large piston provide if the small piston is pushed down with a force F, of 18.0 N? Assume that the fluid used in the lift is incompressible. F, = F, y2 A, A, F,
A water intake at a pump storage reservoir (see the figure below) has a cross-sectional area of 0.637 m². The water flows in at a speed of 0.470 m/s. At the generator building, at distance D = 156 m below the intake point, the cross-sectional area is smaller than at the intake and the water flows out at 9.44 m/s. What is the difference in pressure between inlet and outlet? Reservoir Number 202.6 Units D Intake MPa Generator building Outlet-
A hydraulic car lift has an input piston of radius 2.9 cm and negligible weight. The output piston has a radius of 67 cm. If you push in on the input piston with a force of 200 N, how much pressure are you applying to the system? What force will be transferred into the output piston?
A hydraulic jack piston has a diameter of 0.06 m. The hydraulic jack is connected to another piston that supports the load. The support load piston has a diameter of 0.50 m. If the jack can lift a mass up to 2500 kg, what is the maximum force that one needs to apply to the piston in order to lift the given mass?
A collapsible plastic bag (Fig. F9.11) contains a glucose solution. If the average gauge pressure in the vein is 1.33 × 103 Pa, what must be the minimum height h of the bag to infuse glucose into the vein? Assume the specific gravity of the solution is 1.02.12. A hydraulic jack, has an input piston of area 0.050 m2 and an output piston of area 0.70 m2 . How much force on the input piston is required to lift a car weighing 1.2 × 104 N?
A force of F₁ = 355 N is applied to a hydraulic jack pump piston with a diameter of D₁ = 0.0190 m. What is the magnitude of the output force F2 (in N) if the lifting piston has a diameter of D₂ = 0.143 m [round your final answer to zero decimal places]? {Acircle = (π/4)d²} F₁ A₁ F₂ A₂
The diameters of the pistons on a hydraulic press are 5.0 cm and 40 cm. When a force of 50 N is exerted on the smaller piston, what force can the larger piston exert? {A = Bd2/4}Answer is in Newton
As shown in the figure below, a hydraulic system has two pistons of different diameter and uses a liquid of density p = 850 kg/m³. The smaller piston has a diameter of 4.7 cm and a mass of 1.6 kg and the larger piston a diameter of 14 cm and a mass of 2.8 kg. Determine h, the height difference between the two pistons. m
A force of F1 = 345 N is applied to a hydraulic jack pump piston with a diameter of D1 = 0.0168 m. What is the magnitude of the output force F2 (in N) if the lifting piston has a diameter of D2 = 0.120 m [round your final answer to zero decimal places]? {Acircle = (π/4)d2}