The small piston of a hydraulic lift (see figure below) has a radius of r1= 1.00 cm, and its large piston has a radius of r2=9.45 cm. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load of mass 1500 kg? Answer: |N.

The small piston of a hydraulic lift (see figure below) has a radius of r1= 1.00 cm, and its large piston has a radius of r2=9.45 cm. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load of mass 1500 kg? Answer: |N.

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 6P: The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its...

See similar textbooks

Related questions

Q: filling station uses a Venturi tube to measure the flow rate of gasoline. The density of the…

A: ABernailli equation gives usP1+12ρv12+ρgh1=P2+12ρv22+ρgh2h1≈h2so neglect…

Q: Consider the hydraulic system in fig. 4. Develop a model for this system that can be used to find H1…

A: GIVEN: F1=K1H1F2=K2H2 where H1 and H2 are the functions of time for any given variations in inputs.…

Q: A fluid-filled chamber has a piston has with a surface a cross-sectional area of 8.00 cm2 on one…

Q: For the system shown in the Figure P 175 x 10 Pa and P, 1.20 x 104 Pa. Let y 25 cm and the volume…

Q: A tall cylinder with a cross-sectional area 12.0 cm2 is partially filled with mercury; the surface…

Q: Piston A has a cross sectional area of 1400 mm2 While that of piston B is 1000 mm2. B is higher than…

A: Let Pa be defined as the pressure at piston A. Therefore, Here, Fb is the force. Aa is the area.

Q: In the figure, a spring of spring constant 3.90 x 104 N/m is between a rigid beam and the output…

A: Given Value of the spring constant and area of input and output piston . Our task is to calculate…

Q: Pistons are fitted to two cylindrical chambers connected through a horizontal tube to form a…

Q: F₁ A₁ F₂ A₂

A: F1 = 205 N d1= 0.015 m d2 = 0.25 m Let output force is ' F2 ' .

Q: The density of the liquid flowing through the horizontal pipe in the drawing is 1200 kg/m3. The…

A: Given Density of the fluid is ρ=1200 kg/m3 Speed of the fluid at point A is vA=7.5 m/s Speed of the…

Q: In the hydraulic system, the piston on the left hasa diameter of 5.1 cm and a mass of 2.3 kg. The…

A: Write the expression for the pressure at left.

Q: Pistons are fitted to two cylindrical chambers connected through a horizontal tube to form a…

Q: A cylindrical storage tank has a cross sectional area A1=1.5 m². The tank is set up vertically on…

Q: A force of 30. N is applied to the input piston of a hydraulic jack. If the input and output piston…

A: Given data: Force on input piston (F1) = 30 N Area of input piston (A1) = 0.20 m2 Area of output…

Q: A hydraulic jack has input piston with cross-sectional area 0.05 m2 and output piston with…

A: Given Data: The cross-sectional area of the input piston is: Ai=0.05 m2 The cross-sectional area of…

Q: Pressure in the spinal fluid is measured. If the pressure in the spinal fluid is 10.0 mm Hg: (a)…

A: P0=Pressure in the spinal fluid=10 mm Hgρ=Density of fluid=1.05 g/mL=1.05×103 kg/m3g=Acceleration…

Q: what maximum mass can be lifted by the output piston?

A: Given: Radius of the pistons, r1=4.00cm and r2=18.0cm Exerted force at the input piston, F1=825N

Q: A tall cylinder with a cross-sectional area 12.0 cm2 is partially filled with mercury; the surface…

Question

The small piston of a hydraulic lift (see figure below) has a radius of r1= 1.00 cm, and its large piston has a radius of r2=9.45 cm. What downward force of magnitude F1 must be applied to the small
piston for the lift to raise a load of mass 1500 kg? Answer:
N.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, physics and related others by exploring similar questions and additional content below.

Similar questions

The small piston of a hydraulic lift (Fig. P15.6) has a cross-sectional area of 3.00 cm2, and its large piston has a cross-sectional area of 200 cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0 kN? Figure P15.6
Liquid toxic waste with a density of 1752 kg/m3 is flowing through a section of pipe with a radius of 0.312 m at a velocity of 1.64 m/s. a. What is the velocity of the waste after it goes through a constriction and enters a second section of pipe with a radius of 0.222 m? b. If the waste is under a pressure of 850,000 Pa in the first section of pipe, what is the pressure in the second (constricted) section of pipe?
A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?
Review. The tank in Figure P15.13 is filled with water of depth d = 2.00 m. At the bottom of one sidewall is a rectangular hatch of height h = 1.00 m and width w = 2.00 m that is hinged at the top of the hatch. (a) Determine the magnitude of the force the water exerts on the hatch. (b) Find the magnitude of the torque exerted by the water about the hinges.
(a) What is the fluid speed in a fire hose with a 9.00-cm diameter carrying 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
A tank with a flat bottom of area A and vertical sides is filled to a depth h with water. The pressure is P0 at the top surface. (a) What is the absolute pressure at the bottom of the tank? (b) Suppose an object of mass M and density less than the density of water is placed into the tank and floats. No water overflows. What is the resulting increase in pressure at the bottom of the tank?
The gravitational force exerted on a solid object is 5.00 N. When the object is suspended from a spring scale and submerged in water, the scale reads 3.50 N (Fig. P15.24). Find the density of the object. Figure P15.24 Problems 24 and 25.
In an immersion measurement of a woman's density, she is found to have a mass of 62.0 kg in air and an apparent mass of 0.0850 kg when completely submerged with lungs empty. (a) What mass of water does she displace? (b) What is her volume? (c) Calculate her density. (d) If her lung capacity is 1.75 L is she able to float without treading water with her lungs filled with air?
A rock with a mass of 540 g in air is found to have an apparent mass of 342 g when submerged in water. (a) What mass of water is displaced? (b) What is the volume of the rock? (c) What is its average density? Is this consistent with the value for granite?
What is the fluid speed a hose a 9.00-cm diameter 80.0 L of water per second? (b) What is the flow rate in cubic meters per second? (c) Would your answers be different if salt water replaced the fresh water in the fire hose?
Figure P15.47 shows a stream of water in steady flow from a kitchen faucet. At the faucet, the diameter of the stream is 0.960 cm. The stream fills a 125-cm3 container in 16.3 s. Find the diameter of the stream 13.0 cm below the opening of the faucet. Figure P15.47
Pressure in the spinal fluid is measured as shown in Figure 11.43. If the pressure in the spinal fluid is 10.0 mm Hg: (a) What is the reading of the water manometer in cm water? (b) What is the reading if the person sits up, placing the top of the fluid 60 cm above the tap? The fluid density is 1.05 g/mL. Figure 11.43 A water manometer used to measure pressure in the spinal fluid. The height of the fluid in the manometer is measured relative to the spinal column, and the manometer is open to the atmosphere. The measured pressure will be considerably greater if the person sits up.