The drawing shows a hydraulic chamber with a spring (spring constant = 1500 N/m) attached to the input piston and a rock of mass 50.0 kg resting on the output plunger. The piston and plunger are nearly at the same height, and each has a negligible mass. By how much is the spring compressed from its unstrained position? Area = 15 cm2 Area = 65 cm2

The drawing shows a hydraulic chamber with a spring (spring constant = 1500 N/m) attached to the input piston and a rock of mass 50.0 kg resting on the output plunger. The piston and plunger are nearly at the same height, and each has a negligible mass. By how much is the spring compressed from its unstrained position? Area = 15 cm2 Area = 65 cm2

Name: Solve The drawing shows a hydraulic chamber with a spring (spring cons
Uploaded: 2024-03-20T06:51:10.000Z
Channel: Bartleby
Description: Solve The drawing shows a hydraulic chamber with a spring (spring constant = 1500 N/m) attached to the input piston and a rock of mass50.0 kg resting on the output plunger. The piston and plunger are nearly at the same height, and each has a negligib

Principles of Physics: A Calculus-Based Text

5th Edition

ISBN:9781133104261

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter15: Fluid Mechanics

Section: Chapter Questions

Problem 55P

See similar textbooks

Similar questions

The lintel of prestressed reinforced concrete in Figure P12.27 is 1.50 m long. The concrete encloses one steel reinforcing rod with cross-sectional area 1.50 cm2. The rod joins two strong end plates. The cross-sectional area of the concrete perpendicular to the rod is 50.0 cm2. Youngs modulus for the concrete is 30.0 109 N/m2. After the concrete cures and the original tension T1 in the rod is released, the concrete is to be under compressive stress 8.00 106 N/m2. (a) By what distance will the rod compress the concrete when the original tension in the rod is released? (b) What is the new tension T2 in the rod? (c) The rod will then be how much longer than its unstressed length? (d) When the concrete was poured, the rod should have been stretched by what extension distance from its unstressed length? (e) Find the required original tension T1 in the rod. Figure P12.27
Because atmospheric pressure is about 105 N/m2 and the area of a persons chest is about 0.13 m2, the force of the atmosphere on ones chest is around 13 000 N. In view of this enormous force, why dont our bodies collapse?
A copper rod with length 1.4 m and cross-sectional area 2.0 cm2 is fastened to a steel rod of length L and cross-sectional area 1.0 cm2. The compound structure is pulled on each side by two forces of equal magnitude 6.00 104 N (Fig. P14.57). Find the length L of the steel rod if the elongations (L) of the two rods are equal. Use the values Ysteel = 2.0 1011 Pa and YCu = 1.1 1011 Pa. FIGURE P14.57
A horizontal pipe 10.0 cm in diameter has a smooth reduction to a pipe 5.00 cm in diameter. If the pressure of the water in the larger pipe is 8.00 104 Pa and the pressure in the smaller pipe is 6.00 104 Pa, at what rate does water flow through the pipes?
A host pours the remnants of several of wine into a jug a party. The host then inserts a cork with a 2.00-cm diameter into the bottle, placing it in direct contact with the wine. The host is amazed when the host pounds the cork into place and the bottom of the jug (with a 14.0-cm diameter) breaks away. Calculate the extra force exerted against the bottom if he pounded the cork with a 120-N force.
Review. In a water pistol, a piston drives water through a large tube of area A1 into a smaller tube of area A2 as shown in Figure P14.46. The radius of the large tube is 1.00 cm and that of the small tube is 1.00 mm. The smaller tube is 3.00 cm above the larger tube. (a) If the pistol is fired horizontally at a height of 1.50 m, determine the time interval required for the water to travel from the nozzle to the ground. Neglect air resistance and assume atmospheric pressure is 1.00 atm. (b) If the desired range of the stream is 8.00 m, with what speed v2 must the stream leave the nozzle? (c) At what speed v1 must the plunger be moved to achieve the desired range? (d) What is the pressure at the nozzle? (e) Find the pressure needed in the larger tube. (f) Calculate the force that must be exerted on the trigger to achieve the desired range. (The force that must be exerted is due to pressure over and above atmospheric pressure.) Figure P14.46
A light, cubical container of volume a3 is initially filled with a liquid of mass density as shown in Figure P15.5la. The cube is initially supported by a light string to form a simple pendulum of length Li, measured from the center of mass of the filled container, where Li a. The liquid is allowed to flow from the bottom of the container at a constant rate (dM/dt). At any time t, the level of the liquid in the container is h and the length of the pendulum is L. (measured relative to the instantaneous center of mass) as shown in Figure P15.51b. (a) Find the period of the pendulum as a function of time. (b) What is the period of the pendulum after the liquid completely runs out of the container? Figure P15.51
The drawing below shows a hydraulic chamber in which a spring (spring constant = 1620 N/m) is attached to the input piston (A1 = 12.7 cm2), and a rock of mass 38.2 kg rests on the output plunger (A2 = 62.8 cm2). The piston and plunger are nearly at the same height, and each has a negligible mass. By how much is the spring compressed from its unstrained position?
A hydraulic chamber in which a spring (spring constant = 1550 N/m) is attached to the input piston (A1 = 14.1 cm^2), and a rock of mass 36.1 kg rests on the output plunger (A2 = 67.8 cm^2). The piston and plunger are nearly at the same height, and each has a negligible mass. By how much is the spring compressed from its unstrained position?
A hydraulic press has a safety feature which consists of a hydraulic cylinder with a piston at one end and a safety valve at the other. The cylinder has a radius of 0.0220 m and the safety valve is simply a 0.00800-m radius circular opening at one end, sealed with a disk. The disk is held in place by a spring with a spring constant of 825 N/m that has been compressed 0.0095 m from its natural length. Determine the magnitude of the minimum force that must be exerted on the piston in order to open the safety valve. N
A light spring of constant 165 N/m rests vertically on the bottom of a large beaker of water.A 4 kg block of wood of density 649 kg/m3is connected to the top of the spring andthe block-spring system is allowed to come tostatic equilibrium.What is the elongation ∆L of the spring?The acceleration of gravity is 9.8 m/s2.Answer in units of cm.
The drawing shows a hydsraulic chamber with a spring (string constant = 1250N/m) attached to the input piston and an object of 38 kg (resting on the output plunger). The piston and plunger are at the same height each having a negligible mass. By how much is the spring compressed from its unstrined position?