civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3 Resistive force. V=0.3 m/sec S=0.88 M= 0.65 centi poise → Bottom plate Direction of shear force on top plate Bottom plate & fluid element

civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3 Resistive force. V=0.3 m/sec S=0.88 M= 0.65 centi poise → Bottom plate Direction of shear force on top plate Bottom plate & fluid element

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The column above is subjected to axial loading only. Assume the following: • E= 29000 ksi G = 10000 ksi • = 986 in4 A = 60 in? • L= 20 ft • Grade 60 steel (60 ksi yield stress) • The column is fixed at the top and pinned at the bottom Which of the following is closest to the maximum normal stress the column can support (before yielding or buckling)? 167 ksi 24 ksi 42 ksi 60 ksi
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,, = 345 MPa) for %3D the C-frame material. Calculate the location of centroidal axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 25 mm 10 mm 90 mm A+ A 10 mm
Three identical circular A36 steel columns, A, B, and C, are carrying a 750kN block. The diameter of each column is 30mm. Calculate the normal stress on each column when column B is heated from 20oC to 25oC. Consider: EA36 =200GPa  A36 =0.000012 oC-1 1) What is the effect of column length on the result? 2) Is this structure statically determinate or indeterminate? Why?
The prismatic rod shown is made of a steel that is assumed to be elastoplastic with E = 200 GPa and oy = 280 MPa. Knowing that couples M and M' of moment 525 N·m are applied and main- tained about axes parallel to the y axis, determine (a) the thick- ness of the elastic core, (b) the radius of curvature of the bar. y M 18 mm 24 mm X 'M'
YIELD AND MOVE tO GE THERA DISTAHCE OF O.5mm A 25m STEEL ROD WITH A CRO6S-SECTIONAL ÅREA OF 1250mm? IS SECURED BETWEEH RIGID SUPPORTS AT BOTH ENDS. IF THERE IS NO STRESS AT A TEMPERATURE OF 20°C, E- 200000 MPa. a. COMPUTE THE STRESS WHEN THE TEMPERATURE DROPS TO O°C, IF IT HAS A COEFFICIENT OF THERMAL EXPANSION OF 0. 0000||7 m/m°C. b COMPUTE THE STRAIN OF THHE ROD IF THE ROD SUPPORTS YIELD AND MOVE TOGETHER A DISTANCE OF O.5mm AS TEMPERATURE DROPS. C. COMPUTE THE STRESS IH THE ROD IF THE SUPPORTS AS THE TEMPERATURE DROPS. CS Scanned with CamScanner
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
Which of the following nearly gives the frictional force at the 550lb block? a. 200 lb b. 420 lb c. 320 lb d. 140 lb
Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v=0.33] pipe has an outside diameter of 225 mm, a wall thickness of 15 mm, and a length of 5.0m. The pipe supports a compressive load of 670 kN. After the temperature of the pipe drops 48°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) 8 = mm AD= i mm
Required information Consider the loading shown. The allowable normal stress for the steel used is 160 MPa. 0.8 m 50 kN/m B -2.4 m- 0.8 m For the selected design, determine the actual value of Om in the beam. (Round the final answer to one decimal place. You must provide an answer before moving to the next part.) The actual value of om in the beam is 160 MPa.
32 H.W tind longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal Bessure is 0.9 Ma and thickness of Wall is 6.4 mm? Ansi é =42.19 MPa + F= 62.8 Ma Also find ?5067 0.6m 0.6m
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN