730Enercise:-diameter of12mmA cylindrical rod 100 mm long withis subjected to a30000 N. Assuming that thetensileload ofdeformation is entirely elastic andallowable elevation in pligmeterisallowable reduction in dligmeter is 0.015mm. chooseamoryonlymeeting requirentU (Poiss ons vahu)0.33belowMaterialAluminium alloyBronzeTitanium allowmanimum0.3 mm while manimumE (GPa)701001100.343

To choose the suitable material that satisfies the given elongation and reduction in diameter…

Inercise:- a A cylindrical rod 100 mm 12 mm diameter of long with is subjected to a 30000 N. Assumiy and that the ensile load of •formation is entirely elastic. llowable cloration is lowable reduction in dligmeter is 0.015mm. choose below only candidate meeting requirent Material E (GPa) m manimum 0.3 mm while manimum U(Poisson's rahi 37

Inercise:- a A cylindrical rod 100 mm 12 mm diameter of long with is subjected to a 30000 N. Assumiy and that the ensile load of •formation is entirely elastic. llowable cloration is lowable reduction in dligmeter is 0.015mm. choose below only candidate meeting requirent Material E (GPa) m manimum 0.3 mm while manimum U(Poisson's rahi 37

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A uniform edge load of w₁ = 540 lb/in. and W2 = 400 lb/in. is applied to the polystyrene specimen. Ep = 597 (10³) psi and vp = 0.25. (Figure 1) Figure T W₂ b - < 1 of 1
I need the answer as soon as possible
What are the assumptions for the cylindrical and spherical vessels such that the stresses are calculated as follows for the cylinder: in the Hoop direction: o = pr/t the Longitudinal stress: o = pr/2t and for the sphere: O= pr/2t Cevabınızı biçimlendirmek için düzenleyiciyi kullanın
strength-of-materials pressure-vessels Maximum shear stress at any point in a thin cylinder of diameter (d) and thickness (t) subjected to an internal fluid pressure (p) is given by-
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,, = 345 MPa) for %3D the C-frame material. Calculate the location of centroidal axis upto 2 digits after decimal point in mm? 18 mm 38 mm 13 kN 25 mm 10 mm 90 mm A+ A 10 mm
The Brinell's hardness number (B.H.N.) is expressed as P (b) TD TD D-VD²-a² D+VD² -d² (c) (d) P TD D-VD? -d? TD D+\D² - d² where, P= Test force (M), D = Diameter of steel ball (mm), d = Mean diameter of the indent (mm) %3D %3D
r Two Example (2) 8- A compound bar is constructed from three.. wide by 12mm thick together to form a bar somm wide 30 The middle bar is of aluminum alloy for which F-70 GP= outside of brass with E-100 MPa. If the bars are initia at 18c and the temperature of the whole assembly is to to So C, determine the stresses set up in the brass and the Kg = 18 510 Solutions2 FB = FAL FB So*12*10 63 Ext. + Comp. = (XAI - XB) L.A.T. FB.L FAL.L AAL.EAL Ag Eg = DAL + From these equation & FAL=3984 N FB 1992. N 1992 50*121610-6 FB AB -6 XA => 22 *10°-=-=- = (XAL-XB) LAT FAL *100*109 So*12*10% 70 4109 FAL 3984 AAL SO#1210-6 SB = SAL How find that?! = 32. MPa (Ton) FAL. L AP EA = (22-18) x 10² (50-18) XIF_P=15 KN (camp.) Find O'B and GAL F₁+ 2FB = 15 6.64 MPa: (comp)... L FB.L AB. E.B ww.as 17 Brass AL Brass
(b) (ii) A 20 mm diameter rod made from 0.4% C steel is used to produce a steering rack. If the yield stress of the steel used is 350 MPa and a factor of safety of 2.5 is applied, what is the maximum working load that the rod can be subjected to? 2
A small element is under loading where o, =-22 MPa, o, =22 MPa and tgy =14 MPa. Taking the yield stress as 56 MPa, analyze whether the yielding occurs or not by maximum distortion energy criterion. If it does not yield, determine how safe it is.
I need the answer as soon as possible
A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a djameter of 70 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 71 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? Answer: P = KN