A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,= 345 MPa) for %3D the C-frame material. Calculate the location of centroidal axis upto 2 digits after decimal point in mm?

A 13-kN hydraulic press for removing and reinstalling bearings in small-to medium-sized electric motors is to consist of a commercially available cylinder mounted vertically in a C- frame, with dimensions as sketched in the Figure shown below. It is being proposed to use ASTM A-48 (Class 50) gray cast iron (brittle material with ultimate strength, s,= 345 MPa) for %3D the C-frame material. Calculate the location of centroidal axis upto 2 digits after decimal point in mm?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 35 mm, an inside diameter of 30 mm, and a shear modulus of G2 - 45 GPa. The solid steel core has a diameter of 30 mm and a shear modulus of G2 - 85 GPa. Assume L - 380 mm. The composite shaft is subjected to a torque of T- 800 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. (1) L B Answers: MPa (a) TI = MPa rad (b) PBIA =
i need the answer quickly
Please show the full solution, thank you
H.W.6: A hollow circular cold-rolled bronze [G, = 6,500 ksi] tube (1) with an outside diameter of 1.75 in. and an inside diam- eter of 1.25 in. is securely bonded to a solid 1.25-in.-diameter cold-rolled stainless steel [G2 = 12,500 ksi] core (2) as shown in Figure and the allowable shear stress of core (2) is 60 ksi. Determine . The allowable shear stress of tube (1) is 27 ksi, (a) the allowable torque T that can be applied to the tube-and- core assembly. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced in a 10-in. length of the assembly by the allowable torque T. (1) т. FIGURE
Solution.
A high-strength steel band saw, 24 mm wide, runs over pulleys 900 mm in diameter. What minimum thickness of the steel band can be used without exceeding a flexural stress of 310? Assume E= 230 GPa. Answer must be in mm.
Two aluminum plates, each having a width b = 7.5” and thickness t = 2”, are welded together as shown in the figure. Assume that a = 5.0”. Specifications require that the normal and shear stress magnitudes acting in the weld material may not exceed 40 ksi and 25 ksi, respectively.
A high-density polyethelene (HDPE) [E = 780 MPa; v = 0.46] rod has a diameter of 100 mm before load P is applied. In order to maintain certain clearances, the diameter of the rod must not exceed 102 mm when loaded. What is the largest permissible compressive load P that can be applied to the HDPE rod? P. High-density polyethelene (HDPE) rod Answer: P = i P kN
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P
A rod must not stretch more than 6 mm when the tension in the wire is 8 kN. Knowing that E-105 GPa and that the maximum allowable normal stress is 150 MPa determine the smalest diameter rod that shouid be used in mm
i need the answer quickly
Please show intermediate steps including free body diagrams, equations used, and problem setup so that your approach can be followed.