Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in, Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A (1) (2) Answer: uca- in.

Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area of 1.71 in and an elastic modulus of 2050 ksi. Bar (2) has a cross-sectional area of 1.019 in? and an elastic modulus of 3910 ksi. Assume L-20 in, Lyn47 in. Q-6 kips. P-3.6 kips, and R-13.2 kips. Determine the horizontal deflection of end Crelative to end A (1) (2) Answer: uca- in.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Similar questions

The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Two polymer bars are connected to a rigid plate at 8, as shown. Bar (1) has a cross-sectional area of 1.42 in.and an elastic modulus of 2180 ksi. Bar (2) hasa cross-sactional area of 1139 in.and anelastic modulus of 4150 ksi. Assume l-23 in., L-41 in, Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Datermine the horizontal deflection of end Crelative to end A P R (1) (2) Answer: uga in.
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.58 in. and an elastic modulus of 2430 ksi. Bar (2) has a cross-sectional area of 0.714 in and an elastic modulus of 4110 ksi. Assume Ly-18 in., Lz-47in, Q=6,4 kips, P-3.2 kips, and R-128 kips. Determine the horizontal deflection of end Crelative to end A. (1) Answer: uCA in.
X Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.42 in.? and an elastic modulus of 2180 ksi. Bar (2) has a cross-sectional area of 1.139 in.? and an elastic modulus of 4150 ksi. Assume L;-23 in., L2-41 in., Q-6.7 kips, P-3.7 kips, and R-14.1 kips. Determine the horizontal deflection of end Crelative to end A. R (1) (2) P L1 L2 Answer: UCIA - i 0.0725 in.
The shown plate is 60 mm thick and it is made of Magnesium Am1004-T61. The plate is fitted between the rigid frictionless supports as shown and at T, = 20°C it is stress free. Find the stresses in the x and y directions when the temperature increases to T, = 58°C. %3D 150 mm 150 mm Select one: O x: 0 MPa, y: 42.864 MPa Ox: 22.1 MPa, y: 44.2 MPa Ox: 0 MPa, y: 44.2 MPa Ox: 0 MPa, y: 17.8 MPa O x: 13.2 MPa, y: 44.2 MPa Ox: 0 MPa, y: 67.4 MPa 3:10 PM O G 4) ENG 1/31/2021
STRAIN
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
A bar obtained by bonding together pieces of steel (Es = 29 x 106 psi) and brass (E = 15 x 106 psi) has the cross section shown (Fig. a). Determine the maximum stress in the steel and in the brass when the bar is in pure bending with a bending moment M = 40 kip-in. 0.4 in. 3 in. Brass 0.75 in. Steel Brass 0.4 in. (a) 1) Composite bar.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P in kN that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa
Engineering Mechanics. Please help to provide solution.
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
R14-7 The principal stresses at a point are shown in the figure. If the material is A36 steel, determine the principal strains. 84 MPa 140 MPa 6 MPa