An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0×10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 260 mm, a cross-sectional area of A = 14720 mm2, and a length of L = 5.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1680 µɛ. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. L P Answer: Ad = i mm

An aluminum alloy [E = 70 GPa; v = 0.33; a = 23.0×10-6/°C] bar is subjected to a tensile load P. The bar has a depth of d = 260 mm, a cross-sectional area of A = 14720 mm2, and a length of L = 5.5 m. The initial longitudinal normal strain in the bar is zero. After load P is applied and the temperature of the bar has been increased by AT = 46°C, the longitudinal normal strain is found to be 1680 µɛ. Calculate the change in bar depth d after the load P has been applied and the temperature has been increased. L P Answer: Ad = i mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 880 mm. The cross-sectional dimensions of the beam are b1 = 37 mm, d1 = 86 mm, b2 = 22 mm, d2 = 22 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 11 MPa, and the allowable compressive bending stress is 9 MPa. Determine the largest moment M that can be applied as shown to the beam.
An extruded polymer beam is subļected to a bending moment M. The length of the beam is L = 860 mm. The cross-sectional dimensions of the beam are bq = 36 mm, d = 89 mm, b2 = 22 mm, d2 = 22 mm, and a = 7 mm. For this material, the allowable tensile bending stress is 10 MPa, and the allowable compressive bending stress is 10 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 ja a M d2 d1 A B b1 Answer: 410.8451 N-m
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
An aluminum alloy rod has a circular cross section with a diameter of 7mm. The rod is subjected to a tensile load of 5kN. Assume that the material is in the elastic region and E = 69 GPa. If Poisson's Ratio is 0.38, what will be the lateral strain? E=6/8 v= -€(lateral)/e(axial) V ominorbooomes
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b₁ = 33 mm, d₁ = 109 mm, b₂ = 20 mm, d₂ = 20 mm, and a = 6.5 mm. For this material, the allowable tensile bending stress is 16 MPa, and the allowable compressive bending stress is 11 MPa. Determine the largest moment M that can be applied as shown to the beam. b₂ a M B A Answer: M = L d₂ N•m b₁ d₁
The stainless steel specimen is shown in Figure 3 with tensile engineering stress-strain behaviour. a)Compute the modulus of elasticity. and Compute the yield strength at a strain offset of 0.002.
2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at which the normal stress in the aluminum bar will be equal to -11 ksi, (b) the corresponding exact length of the aluminum bar. 0.02 in. -14 in. 18 in. Aluminum A = 2.8 in² Bronze A = 2.4 in² E = 15 × 10º psi a = 12 x 10-6/°F E = 10.6 × 106 psi α = 12.9 x 10-6/°F Fig. P2.58 and P2.59
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b₁ = 38 mm, d₁ = 82 mm, b₂ = 23 mm, d₂ = 23 mm, and a = 7.5 mm. For this material, the allowable tensile bending stress is 14 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b₂ a M d₁ B L N-m | A Answer: M= d₂ b₁
A certain steel has proportionality limit of 300 N/mm² in simple tension. Under a Three Dimensional Stress System, the principal stresses are 150 N/mm² (Tensile), 75 N/mm² (Tensile) and 30 N/mm² (Compressive), μ = 0.3. The factor of safety according to maximum shear stress theory would be
I5 In a tensile test experiment of carbon steel. a standard specimen (D= 0.505 in. Gauge length=2.0 in & total length 8 in) had a 0.2% offset yield strength of 80.000 psi and engineering strain of 0.010 at the yield strength point Calculate: The load (force) at this point. The instantaneous area of the specimen at this point. c. The true stress at this point. d. The true strain at this point. e. The total length of the specimen. if the load is released at this point.
An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam are b, = 35 mm, d = 115 mm, b2 = 21 mm, d, = 21 mm, and a = 7 mm. For this material, the allowable tensile %3D %3D bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 立 a 不 d2 d1 A Answer: N.m M= i Submit Answer Attempts: 1 of 3 used
choose the correct answer