NO AI PLEASE Calculate the required current for a 1-phase load of 1MW, VLN =120V, PF = 0.95 lagAmpsCalculate the required current for a 3-phase load of 2MVA, VLN =208V, PF = 0.85 leadingAmps

Answered: Calculate the required current for a…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Similar questions

3. The secondary voltage can rise above its rated value when the load is a. resistive. b. capacitive. C. inductive. d. an RL series combination.
In general, the greater the absolute value of the impedance in a circuit:A. The greater the flow of alternating current.B. The less the flow of alternating current.C. The larger the reactance.D. The larger the resistance.
Please address the question in the attached photo. Thank you.
3-phase transfomer configuration in figure imagen: Ammeter A4 is measuring_______, Ammerter A5 is measuring_____, Ammerter A6 is measuring___, Voltmeter V1 is measuring_____, voltmeter V2 is measuring____, Voltmeter V3 is measuring ______, Voltmeter V4 is measuring_____,Voltmeter V5 is measuring______. A- line voltage B-phase voltage C- meither "a" nor "b" d- both "a" and "b"
A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
a capacitor and a resistor are connected in parellel to a 120 v 60 hz line the resistor has a resistance of 40 ohms and the capacitor has a capacitance of 132.6 uf what is the total current flow through the circuit. what is the impedence and the power factor and how many degrees out of phase are the current and voltage out phase with eachother.
Zener Diodes: In the following diagram, Iz = 0.5 mA, Vz = 5, rz = 30 ohms. What is Vout? What is the current through D5? Current through D7?
Given the zener voltage at 9V and the zener power at 1W, what is the range of allowable values of Iz (operating values). Choices: 0.11A 22mA to 89mA 9A 0.11A to 9A Plss show complete solution
A voltage-multiplier has a Vm = 60 V peak sinusoidal secondary voltage. Calculate the voltage across C2 and C4. A 120 V B 240 V C 180 V D 60 V
NEED ASAPPP 3. Determine the minimum and maximum output voltages for the voltage regulator in Figure.Assume I ADJ = 50 μA. Set R 1 = 122 ohms, R 2 = (19) kΩ (maximum)

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Calculate the required current for a 1-phase load of 1MW, VLN =120V, PF = 0.95 lag Amps Calculate the required current for a 3-phase load of 2MVA, VLN =208V, PF = 0.85 leading Amps