Calculate the neutral current in a 120/240-volt, single-phase system when the current inphase A is 20 amperes and the current in phase B is 40 amperes. The load is resistive. Calculate the neutral current in a 208Y/120-volt, 3-phase, 4-wire system when thecurrent in phase A is 0, in phase B is 40, and in phase C is 60 amperes. The load isresistive

Calculate the neutral current in a 120/240-volt, single-phase system when the current inphase A is 20 amperes and the current in phase B is 40 amperes. The load is resistive. Calculate the neutral current in a 208Y/120-volt, 3-phase, 4-wire system when thecurrent in phase A is 0, in phase B is 40, and in phase C is 60 amperes. The load isresistive

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

Q20. The section bus-bars A and B as shown in Figure B5 are linked by a bus-bar reactors each rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA with 12 % reactance. Find the Current and MVA that fed into a dead short circuit between all phases on B with bus-bar reactor in the circuit. Page 4 of 5 جامعة التقنية والعلومر التطبيقية بإبراء University of Technology and Applied Sciences - Ibra Student ID: Section: Student Name: 8,000 kVA 12% 10,000 kVA 10,000 kVA 10% 8,000 kVA 12% 10% 2 3 5,000 kVA 10% lell 8,000 kVA 10% Figure B5 "End of Question Paper"
The principle operation of LVDT is based on the variation of Select one a. Self inductance b. Reluctance c. Mutual inductance d. Permanence
The bus bars of a power station are in two sections A and Bseparated by a reactor. Connected in section A are two 12MVA generators of 15% reactance each and to B, 8 MVAgenerator of reactance 10%. The reactor is rated 8 MVA and15% reactance. Two feeders are connected to bus bar Athrough transformers, each rated at 4 MVA and 5% reactance.Determine the maximum short circuit MVA with which circuitbreakers on the outgoing side of the transformers have todeal.
A 60 Hz, 33 kV, 3-phase alternator with earthed neutral has a reactance of 7 ohms per phase and is connected to a bus-bar through a circuit breaker. The distributed capacitance upto circuit breaker between phase and neutral in 0.03 uF. Determine (i) peak re-striking voltage across the contacts of the breaker (ii) frequency of oscillations
An ac resistance is higher than a dc resistance. True False
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Id is : 510221
Solve and show complete solutions. Choose only from the choices
What is the significance of reactive power in electrical grids, and how is it managed?
Problem 1 - Series en Parallel AC networks [19] Look at the circuit in Figure 1 and determine the following: (a) Total Admittance. (b) Total Impedance. (c) Total Current (l:). (d) Current (I1) through impedance Z2. (e) Current (12) through impedance Z3. (f) Current (I3) through impedance Z4. (g) Is this an inductive or capacitive circuit? A. B Zs 220V;50HZ Figure 1 (h) Voltage across Z1. (i) Voltage across A and B. G) Voltage across Zs. Z1 = 3 + j5 ohm Z2 = 10 + jo ohm Z3 = 5 + j15 ohm Z4 = 10 – j30 ohm Zs = 20 – j30 ohm Admittance and Impedance in rectangular notation. All currents and voltage in polar notation. Take voltage as reference.
The step down DC chopper uses DC source voltage V(dc) = 200 V and resistive load impedance of 10 ohm. The duty cycle is 0.4 the voltage drop across the switch may be taken as zero, Calculate : (a) Average and RMS value of output voltage. (b) Average and RMS value of output current.
hi all could you please solve this problem atta