b)The one-line diagram for a simple power system is given in Figure 1(b).į.Draw the impedance diagram of the system.i.Construct the bus admittance matrix, Xeus and bus impedance matrix,Zous of the system.I.Evaluate the fault current, bus voltages and line current during the flowwhen a balanced three-phase fault occurs on bus 1.bus 1bus 2j65 NGG25 MVA25 MVA13.8 kV15%13.2/69 kV11%25 MVA69/13.2 kV11%15 MVA13 kV15%Figure 1(b)m

Answered: Image /qna-images/answer/11462507-dbcd-4017-975c-77742cb17647.jpg

b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance diagram of the system. i. Construct the bus admittance matrix, YBus and bus impedance matrix, Zous of the system. Evaluate the fault current, bus voltages and line current during the flow when a balanced three-phase fault occurs on bus 1. bus 1 bus 2 j65 N G AY 25 MVA 13.8 kV 15% 25 MVA 13.2/69 kV 11% 25 MVA 69/13.2 kV 15 MVA 13 kV 15% 11% Figure 1(b) m

b) The one-line diagram for a simple power system is given in Figure 1(b). į. Draw the impedance diagram of the system. i. Construct the bus admittance matrix, YBus and bus impedance matrix, Zous of the system. Evaluate the fault current, bus voltages and line current during the flow when a balanced three-phase fault occurs on bus 1. bus 1 bus 2 j65 N G AY 25 MVA 13.8 kV 15% 25 MVA 13.2/69 kV 11% 25 MVA 69/13.2 kV 15 MVA 13 kV 15% 11% Figure 1(b) m

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: fault location

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault Three phase…

Q: The per unit equivalent system of a power system is shown below. It is working at no load when a…

A: In this question we need to find a voltage at bus -3 when a three phase fault occurred at bus 3.

Q: A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the…

A: x=1y=7Note: reactance of element right to bus 4 is not given. Hence we will not consider that in…

Q: pecified in per unit. For generators, assume Z* =Z` =j0.2, Z° = j0.05 For transformers, assume Z' =…

Q: Q5 The single-line diagram of a three-phase power system is shown in Figure Q5a, with equipment…

Q: the fault current for a

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault Three phase…

Q: For the radial power system shown in Figure 3, calculate the line-to-ground fault current flowing in…

A: Apply KVL to find I1.Ps Z42 I1 + Z23 I1 + Z34 I1 – 1(angle 0) = 0 (Z42 + Z23 + Z34) I1 = 1(angle 0)…

Q: jX, (1) 2 3x. iX; E, O E. Figure 1

A: Three phase short circuit occur at bus 2 a) Calculating sub transient generator current Ig…

Q: Refer to Figure 1. Using its equivalent reactance diagram, what is the total impedance of the system…

Q: b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

A: As per the guidelines of Bartleby we supposed to answer 1st three subparts of the question. For…

Q: Symmetrical Fault Analysis Q.13 Topic Power Systems - Symmetrical Fault An... A 100MVA, 33KV…

A: Given- 100 MVA, 33 KV generator- Reactance =0.25 p.u., 0.45 p.u., & 0.05 p.u., To Find- The…

Q: The fault current level of a circuit breaker used in a transmission line with phase voltage 3.3 kV…

A: Given Phase voltage = 3.3kv S = 60 MVA FIND CURRENT

Q: 4. The 33 kV bus-bar of a station are in two sections A and B separated by a reactor. Section 4 is…

Q: The one line diagram of a simple 3-bus power system shown below. All impedances are expresses in per…

A: According to the question, we need to calculate the fault occurred on bus 3 is a three phase fault.

Q: b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

A: POWER SYSTEM: A power system is a network of electrical components that provide, transmit, and…

Q: In a 7-bus system, the double line fault is occurred at bus -5. During fault the positive sequence…

A: Correct option is B Given V01= 0.0175 I = -j0.148

Q: For the following power system, all bus voltages are initially 1 1 pu. Then a three-phase fault…

A: The reactance diagram of the given system will be After a 3-phase fault, the fault point will be…

Q: = For the power system shown below, all reactances are given to the same base 100MVA and 33 KV. A…

Q: 4. The 33 kV bus-bar of a station are in two sections A and B separated by a reactor. Section A is…

A: Given, 33 kV bus-bar of a station are in two sections A and B separated by a reactor. Section A is…

Q: V, =1.025Z0°pu P=300MW j0.05 Bus 1 Bus 3 V = 1.03 Slack j0.025 j0.025 Bus 2 400MW 200MVAR

A: The given power system can be redrawn as shown below:

Q: A 3-phase, 3-wire system has a normal voltage of 10-4 kV between the lines. It is supplied by a…

A: We have 3-Phase, 3-Wire system with, Normal Voltage (Vl) = 10.4 KV = 10.4 * 103 V Generator Positive…

Q: Figure 2 shows the circuit of a simple power system. The ratings of the generators, transformers and…

Q: Consider the single-line diagram of a power system shown below. The transient reactance of cach part…

A: The above question is based on symmetrical fault analysis. All reactances are already given in pu…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

b)
The one-line diagram for a simple power system is given in Figure 1(b).
į.
Draw the impedance diagram of the system.
i.
Construct the bus admittance matrix, Xeus and bus impedance matrix,
Zous of the system.
I.
Evaluate the fault current, bus voltages and line current during the flow
when a balanced three-phase fault occurs on bus 1.
bus 1
bus 2
j65 N
G
G
25 MVA
25 MVA
13.8 kV
15%
13.2/69 kV
11%
25 MVA
69/13.2 kV
11%
15 MVA
13 kV
15%
Figure 1(b)
m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2) The single-line diagram of a three-phase power system is shown in the figure below. The inductor connected to Generator 3 neutral has a reactance of 0.05 per unit using generator 3 ratings as base. Use a 1000-MVA, 765-kV base in the zone of line 1-2. Equipment ratings are given as follows: Synchronous generators: G1 1000 MVA 15 kV G2 1000 MVA 15 kV G3 500 MVA 13.8 kV G4 750 MVA 13.8 kV Transformers: T1 1000 MVA T2 1000 MVA T3 500 MVA T4 750 MVA Transmission lines: 1-2 765 kV 1-3 765 kV 2-3 765 kV 15 kV A/765 kV Y 15 kV A/765 kV Y 15 kV Y/765 kV Y 15 kV Y/765 kV Y X = X₂ = 0.18, Xo = 0.07 per unit X=X₂=0.20, Xo = 0.10 per unit X=X₂ = 0.15, Xo = 0.05 per unit X=0.30, X₂ = 0.40, Xo = 0.10 per unit X₁ = 50 2, Xo = 150 2 X₁ = 40 2, Xo = 100 2 X₁ = 40 2, Xo = 100 2 at Line 1-3 Line 1-2 2 X = 0.10 per unit X = 0.10 per unit X = 0.12 per unit X = 0.11 per unit Line 2-3 3 youtly
The first question has been solved. Qii?
j0.2 For the following power system the impedance matrix is given below. Initially all bus voltages are 1 pu. Then a three-phase fault occurs at bus (2). j0.25 j0.2 (3) (1) j0.1 : (a) What is the fault current? (2) j0.125 j0.1 (b) What are the post-fault bus voltages? 3. 0.0625 0.02083 0.02083' Zbus 0.02083 0.07044 0.02282 0.02083 0.02282 0.06091
The subject is: Smart Grid Applications and Technologies
For the following single line diagram of a three-phase system, a three-phase fault occurs at point P and just before the fault the line voltage is 18 kV at P. Find out the transient fault current in pu and original value at point P. Take, the given kVA and kV of the G1 as the new base. [hint: the transient and sub-transient reactances of the synchronous generators are assumed to be same. But for the motors, assume that the transient one is 1.7 times of the sub-transient reactance.] 20,000 KV A 6.9KV I5メ G1 yo00 KVA 14% 5KV M Tz (G2 11/33KV 33/69 AV lond 5+j8 2 20000KVA 15070 KVA 10% 12% 25,000 KVA 6.9KV [AH the mpedances are given per-unit values) 8% as orebtraen sient ww
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
Q2\ The one-line diagram of a simple power system is shown in figure below. All impedances are expressed in per unit (pu) on a common MVA base. All resistances and shunt capacitances are neglected. The generators are operating on no load at their rated voltage. A three-phase fault occurs at bus 1 through a fault impedance of Zf = j0.08 per unit. Using Thevenin's theorem obtain the impedance to the point of fault and the fault current in per unit. Determine the bus voltages and line currents of generators during fault. X₁ = = 0.1 XT-0.1 3 1 to ojo XL=0.2 2 040 X₁ = 0.1
If the source impedance at a 13.2 kV distribution substation bus is (0:5 + 1:5) Q per phase, compute the RMS and maximum peak instantaneous value of the fault current, for a balanced three-phase fault. For the system (X/R) ratio of 3.0, the asymmetrical factor is 1.9495 and the time of peak is 7.1 ms (see Problem 1). Comment on the withstanding peak current capability to which all substation electrical equipment need to be designed. Problem 1 Consider the expression for i(f) given by i(t) = v21ms [sin(@t-0-)+ sin 0,.eR/X)] where ez = tan-1 (WL/R). (a) For (X/R) equal to zero and infinity, plot i(f) as a function of (wf). (b) Comment on the DC offset of the fault current waveforms. (c) Find the asymmetrical current factor and the time of peak, tp, in milliseconds, for (X/R) ratios of zero and infinity.
Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3, and 345 kV for buses 2, 4, 5. Note that 1-5 and 3-4 are 15/345 kV transformers.a) Draw a one-line diagram of the power system.b) Find the elements Y23, Y43, Y11 Y33 of the system bus admittance matrix.
Q. when a three-phase fault occurs at 75% of the distance from bus G. This fault has 10 arc resistance. 100 MVA, 115 KV Line GH a-Assume that the angle of the mho characteristic is 70°.Determine if the zone I mho unit at H set for 90% of the line GH can operate for this fault. b-Determine the apparent impedance seen by the distance relays at H for this fault. G Z, = 0.365 Z83° - 80% l6 = 1.96 Z–31.42° 4 = 2.60 Z–47.76° ķ = 4.51 Z-40.68° All values in per unit on 100 MVA, 115 kV.