(b) Estimate the total uphill resistance force (F) for a truck with an estimated rolling resistance force of 13272.93N, on the same asphalt road but inclined at Mg = 17% grade with respect to the horizontal axis. What braking force (Fbrake) is required to prevent the truck from any downhill acceleration?

(b) Estimate the total uphill resistance force (F) for a truck with an estimated rolling resistance force of 13272.93N, on the same asphalt road but inclined at Mg = 17% grade with respect to the horizontal axis. What braking force (Fbrake) is required to prevent the truck from any downhill acceleration?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How fast was the car moving the moment the driver removed their foot from the pedal?
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
A solid of mass M=2kg moves up an inclined plane by means of light an inextensible string pulled with a constant force F, of value F = 20N, along the line of greatest slope on the inclined plane. The angle formed by the inclined plane and the horizontal is 0=30. Given g =9.81m/s?. The coefficient of friction is 0.2. 1. Draw a free body diagram showing the forces ..... acting on the solid. 2. Apply the Second Law of Newton to calculate the magnitude of the normal force acting on the solid. 0-30. (Hints: 1- consider the x-axis to be along the inclined plane. 2- The angle between the gravitational force and the negative y-axis is equal to the angle of inclination) 3. Knowing that the coefficient of kinetic friction is 0.2, deduce the magnitude of the friction force. 4. Calculate the acceleration of the solid.
The Beck 550 Spyder described below has manual hydraulic brakes with a single master cylinder. The car is traveling on level ground at sea-level where g = 9.81 m/s². Find the values for the front and rear brake gains that will make this car decelerate at 8.829 m/s², or 0.90g, on a road surface where the peak coefficient of friction is 0.90 when the pedal force is F₂ = 250 N. Neglect the aerodynamic drag and the rolling resistance, but this time include the rotational inertia of the tires and wheels. Answer: G₁ =166.1 N-m/MPa for each front wheel and G, = 114.5 N-m/MPa for each rear wheel. Pedal Assembly The diameter of the master cylinder is DMC = 19.05 mm. The pedal length is Lp = 225 mm. The pushrod for the master cylinder is located at LR = 50 mm. ● ● Pushrod LR Lp Fp Masses, Tire Radius, Wheelbase and Location of the CG Mass of the car with driver, passenger and some stuff: m = 780 kg Inertia of each tire and wheel: I = 0.7 kg-m² Tire rolling radius: r = 0.31 m Wheelbase: L = 2.16…
A block of mass M1 resting on an inclined plane is connected by a string and pulleys to another block of mass M2 as shown in Fig. Find the tension in the string and acceleration of the blocks. Assume the coefficient of friction between the blocks M1 and the plane to be 0.2. M1=1500N , M2=1000N . Angle of inclined glane = 45 degrees
The two ramps pictured here each have a region of length L with kinetic friction coefficient uk and are otherwise frictionless. Identical masses m start at identical heights up the ramps, with the same initial velocity down the ramp. How do their final speeds compare when they reach the far right-hand side? (The answer requested here is qualitative and does not require detailed calculation). L m m Vi #0 Vi O Mass is moving faster in #1 The masses are moving at the same speed. Mass is moving faster in #2 O There is not enough information to decide. L Mk#0 1 2 m m Vf,1 V₁,2
Consider the system shown below. The incline plane is fixed and the coefficient kinetic friction between M and 2M is ?1, and coefficient kinetic friction between the plane and 2M is ?2. Let M=2.0kg, ?=22o, ?1=0.14, and ?2=0.25. (a) What is the magnitude of the frictional force on mass M? (b) What is the magnitude of the total frictional force on mass 2M? (c) What is the acceleration of mass M? (d) What is the acceleration of mass 2M?
Give me right solution with clear calculations
1. The 500-lb block in Fig. P-507/p. 122 is in contact with a 45° incline. The coefficient of static friction is 0.25. Compute the value of the horizontal force P necessary to (a) just start the block up the incline or (b) just prevent motion down the incline (c) If P = 400 lb, what is the amount and direction of the friction force? %3D 500 lb 45 FIG. P-507.
There is a two wheel hub motor driven electric car. This car has the acceleration capability of 1.4 m/s2 at 72 km/h cruising speed of 3000 min-1 motor rotational speed on flat road. Calculate the each motor power at these conditions considering the following parameters of the vehicle. Vehicle mass: 1100 kg Wheel Radius: 0.35 m Aerodynamic drag coefficient: 0.3 Mass Factor: 1.04 + 0.0025 i2 Front projective area: 2.1 m2 Rolling resistance coefficient: 0.02 Density of air: 1.25 kg/m3
Please show clear solutions
Please show clear solutions