what maximum angle can the ramp make with the horizontal before the block starts to slip down?

Q: Steam in a piston-cylinder assembly undergoes a polytropic process, with n=2, from an initial state…

A: Given data:- A polytropic process with a polytropic index n=2 and initial conditions volume…

Q: A long plastic rod of 20-mm diameter (k = 0.3 W/m-K and pc, = 1040 kJ/m3.K) is uniformly heated in…

A: Given: The diameter of rod, d = 20 mm = 0.02 m The thermal conductivity, k = 0.3 W/m.K The…

Q: A chain drive is required to transmit a design power of 4.13 kW from a motor to an output shaft. The…

A:

Q: The velocity of a particle moving in the x-y plane is given by (7.82i +3.51j) m/s at time t = 3.15…

A: Given:To find:

Q: what is the measured distance to the nearest eigthth between the outside corners of the tongue and…

A: FRAMING SQUARE  A framing square, also known as a steel or carpenter square, can be the most…

Q: An ideal Otto cycle has a compression ratio of 9.1. At the beginning of the compression process, air…

A: GivenAn ideal autto cycle r=9:1=9P1=100kPaT1=25oCQ23=1000 kJ/kg

Q: how would you adjust the horizontal plane

A: The horizontal plane is a geometric plane that is perpendicular to the direction of gravity and…

Q: 2.92 For the object shown in Figure P2.92, calculate SA for neutral stability when submerged. А 80…

A: Dear Students The answer is given below

Q: A bar is bent into L shape with 90degree angle. when a force is applied to the end of the point. the…

A:

Q: 3. For the link mechanism if wAB = 2 rad/s as shown, determine WBc when 01 02. Find %3D %3D also Ve…

A:

Q: Determine the magnitude of the pin force at A. Assume W - 875 lb, a = 2.9 ft, b-2.4 ft, r - 6 in. I'…

A:

Q: L P The axially loaded member is pin-connected at one end and fixed at the other. The member has a…

A: There is pin connected at one end and fixed support at other end.The cross sectioin is square of…

Q: 5/4 Specify the x-, y-, and z-coordinates of the mass center of the quarter-cylindrical shell. 360…

A:

Q: Which of the following works by dragging a bucket towards the machine? Dragline Clamshell O Loader…

A: It is required to determine which machine works by dragging a bucket

Q: 1.11 The vacuum pressure of a tank is given to be 40 kPa. If the atmospheric pressure is 95 kPa,…

A: GivenP=40 kPa   vacuumPatm=95kPa

Q: How far have you pulled the block and cylinder when everything stops?

A:

Q: 2. (03) The splined ends and gears attached to the A992 steel shaft are subjected to the torques…

A: Note:- here, part C). and D). has been asked so, I have answered that two parts here.here for steel…

Q: or items 13-20, refer to the compound beam shown. Note: Point 8, Dand, Fare rollers. Point Cand E…

A:

Q: A thin-walled pipe, a uniform cylinder, a uniform sphere, and a bowling ball are all lined up on a…

A: NOTE:- as per honor code and answering guidelines I can answer 1st three subparts at a time.If you…

Q: What is the lowest allowable dimension for the flats?

A: Solution:

Q: What type of simple machine is a wheelbarrow? lever inclined plane O wedge screw

A: A machine used to reduce the effort while performing a task is called a simple machine.

Q: What is the width of the groove on the bolt?

A: Given :- Bolt drawing Find :-  Width of the groove on the drawing = ?

Q: "). A drawing operation is used to form a cylindrical cup with inside diameter = 75 mm, height = 55…

A:

Q: Two infinite parallel plates separated by a distance of H with the upper plate moving at a vec U…

A: LAMINAR FLOW  laminar stream, kind of liquid (gas or fluid) stream in which the liquid ventures…

Q: 12 mm wrench fit over the head of a bolt that is 1/2" across

A: Given: Wrench size =12 mm Bolt size =1/2" AF (across the flat) To determine: Whether the wrench is…

Q: Consider a spring-damper vibration isolation system for a microscope of mass M (shown). harmonic…

A: As there is no any isolation so by decreasing the eccentricity transmitted force get reduced

Q: 21 15 99 TOLL 20

A: To draw: The Front view, Top view and Side view.

Q: Deformed length of the elongated diagonal.

A: Given; A rectangular region in a solid is in a state of plane strain.   The rectangle is subjected…

Q: The neutral point in a drill string can be defined as the point where the string changes from…

A: Answer is true. The neutral point in a drill is the point where there are neither compressive or…

Q: A box is made of wood as shown in the figure below if P=50 lb, the weight of the box =200 Ib, the…

A: Magnitude of force(P)=50lbWeight of the box, W=200lbCoefficient of friction, μ=0.3

Q: Obtain a state-space representation of the mechanical system shown below, where u₁ and u₂ are the…

A:

Q: You are designing a spring-damper vibration isolation system for a microscope (shown). Wn is a…

A:

Q: Y Part B - Clockwise Rotation of a Stress Element with Only One Normal Stress The state of stress at…

A: Note:- As per honor code and answering guidelines I can answer 1st question at a time.If you want…

Q: For what value of w (frequency of the forced harmonic excitation) does the system described by ÿ+9y…

A:

Q: The square steel plate has a mass of 1650 kg with mass center at its center G. Calculate the tension…

A:

Q: Can someone show me how to do the roller, pin, and built-in supports( 2 each) and point them.

A:

Q: Sketch a plot that contains a lateral strain for a material undergoing a temperature change which…

A: Tension or compression occurs when two an tiparallel forces of equal magnitude act on an object…

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: Q1 (a) A container fill with an unknown liquid has three holes as shown in Figure Q1 (a). Determine…

A: Flow rate represents the volume of the water or the fluid flowing per unit of the time through the…

Q: A refrigeration system is to be designed to maintain the temperature in the range of -15°C to -5°C,…

A:

Q: The truss to the right is comprised of members with cross sectional area A = 3 in', length of 12…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.