A long plate is placed parallel to a 13 m/s air stream at 80 kPa and 250 K. At what distance along the plate will theboundary layer be 0.5 mm thick? Give our answer in mm.

Step 1: Step 2: Step 3: Step 4:

Answered: A long plate is placed parallel to a 13…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How does density impact the drag and buoyancy forces?
Contrary to what you might expect, a solid steel ball can float on water due to the surface tension effect. Determine the maximum diameter of a steel ball that would float on water at 10°C. What would your answer be for an aluminum ball? Take the densities of steel and aluminum balls to be 7800 kg/m3 and 2700 kg/m3, respectively.
Consider 0.8-cm-diameter hail that is falling freely in atmospheric air at 1 atm and 5°C. Determine the terminal velocity of the hail. Take the density of hail to be 910 kg/m3.
- Engine oil at 20°C is forced over a 20-cm-square plate at a velocity of 1.2 m/s. The plate is heated to a uniform temperature of 60°C. Calculate the heat lost by the plate, and the drag force exerted on the first 40 cm of the plate using the analogy between fluid friction and heat transfer.
Fruit is impeded from ripening when it reaches high temperatures (>32°C). Farmer Joe isworried that Deleware's summer heat wave will affect the ripening of his ground cherries.The spherical fruit (1 cm in diameter) is surrounded by a spherical papery husk (λhusk = 0.3W/m K) with an inner diameter of 2 cm and an outer diameter of 2.1 cm. The air in betweenthe fruit and the husk is stagnant (λair = 0.03 W/m K). On a calm day in July, the delewareair (outside of the husk) is very warm, with a temperature of ~38°C and a heat transfercoefficient of h deleware,calm = 10 W/m 2K. (a) Sketch the system, labeling all temperatures, dimensions, and proportionality constants. (b) sketch the electrical analogy tothis system, labeling all temperatures, resistances, and heat flows (c) what is the overall resistance to heat transfer from the air in Deleware to the fruit?
A 10-cm-diameter, 30-cm-high cylindrical bottle contains cold water at 3°C. The bottle is placed in windy air at 27°C. The water temperature is measured to be 11°C after 45 min of cooling. Disregarding radiation effects and heat transfer from the top and bottom surfaces, estimate the average wind velocity.
Q9) Consider a 50 cm diameter and 95 cm long hot water tank. The tank is placed on the roof of a house. The water inside the tank is heated to 80°C by a flat-plate solar collector during the day. The tank is then exposed to windy air at 18°C with an average velocity of 40 km/h during the night. Estimate the temperature of the tank after a 45 mm period. Assume the tank surface to be at the same temperature as the water inside, and the heat transfer coefficient on the top and bottom surfaces to be the same as that on the side surface.
60°C glycerin flows over a 15m long flat plate with temperature of 20°C. The velocity of glycerin is 10m/s. Determine the total drag force and the rate of heat transfer per unit width of the entire plate.
A 0.10-mm-diameter glass tube is inserted into water at 100°C in a tub to observe capillary rise phenomenon. Determine the capillary rise of water in the tube. (a) What would happen if the water is cooled down to 20°C? (b) What would happen if 0.10mm tube replaced with 0.3mm tube?
Air at 1 atm and 40°C is flowing over the top surface of a 0.2 m x 0.5 m-thin metal foil. The air stream velocity is 100 m/s and the metal foil is heated electrically with a uniform heat flux of 7500 W/m². If the friction force on the metal foil surface is 0.4 N, determine the surface temperature of the metal foil. Evaluate the fluid properties at 100°C.
A 0.4-W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a circuit board is cooled by air flowing across it at a velocity of 240 m/min. If the air temperature is 35°C, determine the surface temperature of the component. For air properties evaluations assume a film temperature of 50°C. Is this a good assumption?
The top surface of the passenger car of a train moving at a velocity of 70 km/h is 2.8 m wide and 8 m long. The top surface is absorbing solar radiation at a rate of 200 W/m?, and the temperature of the ambient air is 30°C. Assuming the roof of the car to be perfectly insulated and the radiation heat ex- change with the surroundings to be small relative to convec- tion, determine the equilibrium temperature of the top surface of the car. Answer: 35.1°C 200 W/m2 Air 30°C 70 km/h

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

A long plate is placed parallel to a 13 m/s air stream at 80 kPa and 250 K. At what distance along the plate will the boundary layer be 0.5 mm thick? Give our answer in mm.