B - 8 ft

Q: pipe is hung from a barge, is lowered, new sections a stem enables a good degre- an other laving…

A: height of the pipe, h = 2000 mrmin = 400 mdiameter of the pie, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: Air is pumped into the steel thin-walled pressure vessel at C. If the ends of the vessel are closed…

A: Write the given data.

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: When the temperature is 10°C, the two rods are separated by a 0.5-mm 0.5 mm gap as shown. If the…

A:

Q: •4-33. The steel pipe is filled with concrete and subjected to a compressive force of 80 kN.…

A:

Q: When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When…

A: Draw the temperature variation along the pipe.

Q: When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When…

A:

Q: The cylindrical tank with a spherical endcap has an outer radius of 2 m and a wall thickness of 25…

A:

Q: The pipe assembly shown is subjected to a force F = 400 N. The pipe has an inner diameter of 20 mm…

A: from question the data is given as F=400N di=20mm do=30mm Sy =250MPa

Q: Air pressure in the cylinder is increased by exerting forces P = 3 kN on the two pistons, each…

A: Force, P = 3 kN = 3000 N Radius, r = 45 mm = 0.045 m Wall Thickness, t = 2 mm = 0.002 m

Q: The bolt has a diameter of 20 (mm) and passes through a tube that has an inner diameter of 50 (mm)…

A:

Q: The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in.…

A:

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

A:

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A:

Q: At the ambient temperature, the A-36 steel pipe fits snugly between the two fuel tanks. When fuel…

A: Given: The change in length, δL = 4.6 mm The modulus of elasticity, E = 200 Gpa The length of pipe,…

Q: The tank of the air compressor is subjected to an internal pressure of 90 psi. If the inner diameter…

A: Write the given data: Understand that the stress generated at point A will be the tangential stress…

Q: The bolt has a diameter of 20 (mm) and passes through a tube that has an inner diameter of 50 (mm)…

A:

Q: The steel pipe is filled with concrete and subjected to a compressive force of 15 kN and an increase…

A:

Q: A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a…

A: The cross sectional area of steel hoop is  The allowable stress of hoop is The diameter of wood pipe…

Q: A cylindrical pressure vessel is fabricated from steel plating that has a thickness of 20 mm. The…

A: There are two types of stresses that generate in in  thin Pressure vessel.  1) hoop stress that try…

Q: The gas pipe line is supported every 20 ft by concrete piers and also lays on the ground. The gas…

A:

Q: The cylinder head of a steam engine is subjected to a pressure of 1 N/mm2. It is held in position by…

A: Given:Pressure inside cylinder=P=1Nmm2Effective diamter of cylinder=D=300mmNumber of…

Q: A gap of 0.02 in. exists between the composite rod and the wall when the temperature is 75°F. 0.02…

A: Given data: gap=0.02 inTCold=75°FσA=-9 ksi Need to determine the temperature of the aluminum rod.

Q: 4. The steel water pipe has an inner diameter of 100 mm and wall thickness 5 mm. If the flow of…

A:

Q: The gas pipeline is supported every 20 ft by concrete piers and also lays on the ground. If there…

A:

Q: nd hemispherical shells, The bol and the 25 mm diameter bo able normal stress of 150 M

A: given data  tank thickness = 50 mm no of bolt/ length = 40  dia of bolt =25 mm allowable stress for…

Q: The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It is…

A: According to the given condition  We have the stress along its longitude as…

Q: The spherical gas tank is fabricated by bolting together two hemispherical thin shells of thickness…

A: Given t=30mm P=2.5MPa D=8m=8000mm n=900 d=20mm

Q: The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of…

A: Given data: Axial load subjected on the pipe, P = 60 kN. The inner diameter of the pipe, di = 30…

Q: The cylindrical tank with a spherical end cap has an outer radius of 2 m and a wall thickness of 50…

A: (a) Cylinder walls: ◆ Longitudinal stress = 68.25 MPa. ◆ Circumferential stress = 136.50 MPa. (b)…

Q: The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in…

A:

Q: The 3-in.-diameter pipe shown in (Figure 1) carries gasoline at a temperature of 68°F. Figure 8 ft…

A:

Q: The steel pipe is filled with concrete and subjected to a compressive force of 75 kN. Determine the…

A:

Q: F The piston-cylinder assembly above has a wall thickness of 0.125" and an outer radius ro = 2 in.…

A: There are two types of stresses generated in thin cylinders. 1) hoop stress-  It is the maximum…

Q: The two cylindrical rod segments are fixed to the rigid walls such that there is a gap of 0.01 in.…

A: Write the given data with suitable variables. LCu=12 indCu=1.25 inLAl=6 indAl=1.25 inαAl=13×10-6…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.