When filled to capacity, the unpressurized storage tank contains water to a height of h = 43 ft. The outside diameter of the tank is 8.4 ft and the wall thickness is 0.563 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.)

When filled to capacity, the unpressurized storage tank contains water to a height of h = 43 ft. The outside diameter of the tank is 8.4 ft and the wall thickness is 0.563 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: Determine the resultant internal loadings acting on the cross-section at point B.

A: The section of the loading up to B from the end c is shown below: The total load acting per feet in…

Q: xpress the maximum applicable axial force in kilonewtons to three significant figures. The answer…

Q: When the temperature is at 30°C, the A-36 steel pipe fits snugly between the two fuel tanks. When…

Q: Determine the maximum shear stress in the T-beam at section C. Show the result on a volume element…

A: A moment of inertia is a mass of the body when a body is rotating on an axis. The moment of inertia…

Q: The concrete post (E = 3.6 x 10° psi anda = 5.5 x 10-6/F) is reinforced with six steel bars, each of…

Q: Need help with this. Please draw a FBD to help

Q: A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of…

A: Given: The internal pressure in the tank is p=300 kPa. The inner radius of the spherical tank is ri…

Q: Determine the internal normal force, inte nal shear force, and internal moment at point D and at…

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

Q: The concrete post (Ec = 3.6 × 106 psi and αc = 5.5 × 10-6/°F) is reinforced with six steel bars,…

A: To find stress in steel and concrete

Q: The steel water pipe has an inner diameter of 12 in. and wall thickness 0.25 in. (Figure 1) Figure…

A: According to the given datad=12 int=0.25 inP=280 psiWe need to findLongitudinal and hoop stress when…

Q: A pressure vessel has a wall thickness of 8mm and a diameter of 300mm. What is the circumferential…

Q: The steel water pipe has an inner diameter of 12 in. and a wall thickness of 0.25 in. If the valve A…

A: Given Data: The inner diameter of the pipe is d = 12 in. The thickness of the pipe is t = 0.25 in.…

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 49 ft. The…

A: To find: The maximum normal stress and maximum shear stress. Given: The height of water in the tank…

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 27 ft. The…

A: Givenh=27ftd=8.2ftt=0.861 in =0.07175 ftγ=62.4/ft3

Q: A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a…

A: The cross sectional area of steel hoop is The allowable stress of hoop is The diameter of wood pipe…

Q: When filled to capacity, the unpressurized storage tank contains water to a height of h = 41 ft. The…

A: Given:Height of water column, h = 41 ftOutside diameter of the tank, B = 8.5 ftWall thickness, t =…

Concept explainers

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.

Question

When filled to capacity, the unpressurized
storage tank contains water to a height of h
= 43 ft. The outside diameter of the tank
is 8.4 ft and the wall thickness is 0.563 in.
Determine the maximum normal stress and
the absolute maximum shear stress on the
outer surface of the tank at its base. (Weight
density of water = 62.4 lb/ft³.)
Answers:
Maximum normal stress 0 =
i
psi.
h
Maximum shear stress T=
i
psi

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Hoop stress and longitudinal stress calculation

VIEW

Step 3: Maximum normal stress and maximum shear stress calculation

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The pressure tank shown has an outside diameter of 100 mm and a wall thickness of 10 mm. Determine the absolute maximum shear stress at point H on the inner surface if the internal gauge pressure is 1.25 MPa and the applied torque is 375N•m. Show the stress state in matrix form and calculate eigenvalues.
A locomotive semi-elliptical laminated spring has an overall length of 1 m and sustains a load of 70 kN at its center. The spring has 3 full length leaves and 15 graduated leaves with a central band of 100 mm width. All the leaves are to be stressed to 400 MPa, when fully loaded. The ratio of the total spring depth to that of width is 2. E = 210 kN/mm2. Determine the thickness and width of the leaves t = 11.64 mm & W = 109 mm t = 11.14 mm & W 103 mm O t = 11.94 mm & W = 118 mm O t = 11.34 mm & W = 108 mm t = 11.14 mm & W = 118 mm O
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
The beam is made from two plastic pieces glued together at the seam A. If it is subjected to the loading shown, determine the vertical shear force resisted by the flange of the beam at the critical section (in pounds). The supports at C and D exert only vertical reactions on the beam.
The ring, having the dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. Determine the change in the internal radius of the ring after this pressure is applied. The modulus of elasticity of the ring is E. What is the change in internal radius if p = 80 kPa, r = 20 mm, r₁ = 19 mm, and E = 200 GPa? ANS. 1.44 μm tri W
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 3 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of the material after the load is applied.
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 2 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
: The cylindrical pressure vessel with hemispherical end-caps is made of steel. The vessel has a uniform thickness of 0.44mm and an outer diameter of 9.768mm. When the vessel is pressurized to 0.088 MPa, determine the change in the overall length of the vessel. Use E = 200 GPa and µ = 0.3 for steel. Neglect localized bending.R=22
H w help
this section is on morh's circle
3) A thin-walled cylindrical pressure vessel of diameter of 1.5 m is subjected to an internal pressure that varies continuously from p_min= 0.8MPa to p_max = 4 MPa. Determine the pressure vessel thickness, t, if the pressure vessel is made from steel with an ultimate strength S_u=400 MPa, a yield strength S_y=300MPa, and an endurance limit S_n-150MPa and a safety factor of two is desired. Use Modified Goodman and the maximum normal stress theory.