When filled to capacity, the unpressurized storage tank contains water to a height of h = 49 ft. The outside diameter of the tank is 8.2 ft and the wall thickness is 0.765 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.) 1 Answers: h Maximum normal stress o = Maximum shear stress T = i psi. psi

When filled to capacity, the unpressurized storage tank contains water to a height of h = 49 ft. The outside diameter of the tank is 8.2 ft and the wall thickness is 0.765 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.) 1 Answers: h Maximum normal stress o = Maximum shear stress T = i psi. psi

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical tank holding oxygen at 2,058 kPa pressure has an outside diameter of 393 mm and a wall thickness of 13 mm. Compute the longitudinal stress (in MPa) in the wall of the cylinder.
The gas storage tank is fabricated by bolting together two half cylindrical thin shells and two hemispherical shells as shown. If the tank wall has a thickness of 50 mm for cylindrical and hemispherical shells, The bolts were installed as 40 bolts/meter. The tank and the 25 mm diameter bolts are made from material having an allowable normal stress of 150 MPa and 250 MPa, respectively. The tank has an inner diameter of 4 m. What is the maximum pressure that tank can contain.
A spherical gas tank has an inner radius of 6.1 m. If it is subjected to an internal pressure of 445 kPa, determine its minimum required thickness in millimeters (2 decimal places) if the maximum normal stress is not to exceed 12 MPa.
A cylindrical tank having a pressure of 114.0 kPa is used to carry a 3.5 m3of water has a height of 2.0 m and thickness of 5.0 mm. Determine the following What is the diameter of the tank The tangential and longitudinal stress in the tank
If the overhanging beam is made of wood having the allowable tensile and compressive stresses of 4Mpa and 5Mpa, determine the maximum concentrated force P that can be applied at the free end. Can you also please explain the calculation of centroid. I'm a bit confused of the values that I need to use. Thank you
The pressure tank shown has an outside diameter of 100 mm and a wall thickness of 10 mm. Determine the absolute maximum shear stress at point H on the inner surface if the internal gauge pressure is 1.25 MPa and the applied torque is 375N•m. Show the stress state in matrix form and calculate eigenvalues.
The pressure vessel has a thickness 2 cm, diameter 20 cm. Calculate the internal pressure longitudinally and laterally. If the longitudinal stress is limited to 150 MPa and the circumferential stress is limited to 100 MPa. Which one will be used for safety? *
A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response: 8.16 m 3.68 m 07.36 m 4.08 m
i need the answer quickly
A spherical gas tank has an inner radius of r = 1.5 m. If it is subjected to an internal pressure of p = 420 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa.
The assembly consists of a bronze tube fitted over a threaded steel bolt. The nut on the bolt is turned until it is finger-tight. Determine the stresses in the sleeve and bolt when the temperature of the assembly is increased by 200°F. Use the following data: Bronze Steel A (in. ²) 1.5 0.75 a (/°F) 10 × 10-6 6.5 x 10-6 Bronze tube 40 in. E (psi) 12 × 106 29 × 106 STA UT TEO
4. Determine the minimum thickness of the tank plating if the internal pressure is ODD: 1.3MPa EVEN: 1.7MPa and the allowable stress is 33MPa. 300mm 800mm