a) The built-up shaft consists of a pipe AB and solid rod BC. The pipe has an innerdiameter of 20 mm and outer diameter of 28 mm. The rod has a diameter of 12mm. Determine the average normal stress at points D and E and represent thestress on a volume element located at each of these points. Ans: o,=13.3 MPa,%3DОE%3D70.7 MPа.6 kN4 kN8 kN6 kN E

Given data outer diameter of pipe (do) = 28 mm inner diameter of pipe (di) = 20 mm diameter of rod…

Answered: a) The built-up shaft consists of a…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the normal stress in a ball, which has an outside diameter.of 180 mmand a wall thickness of 4.6 mm, when the ball is inflated to a gage pressure of 61 kPa. Answer: o, = MPa
The steel bracket below is used to connect the ends of two cables. If the applied force P=1.50kip, determine the maximum normal stress (in ksi) in the bracket. Assume the bracket is made from a rod having a diameter 1.5in.
2. The cast iron pipe is filled with concrete and subjected to a compressive force of 80 kN. Determine the average normal stress in the concrete and the iron due to this loading. The pipe has an outer diameter of 70 mm and an inner diameter of 60 mm. Eiron = 100 GPa, Ec = 24 GPa. 80 kN 500 mm
%AP n. L. Q.Mid.pdf > Q.: The shaft is hollow from A to B and solid from B to C. Determine the maximum shear stress developed in the shaft. The shaft has an outer diameter of 80 mm, and the thickness of the wall of the hollow segment is 10 mm. 4 kN-m 2 kN-m Q:: Determine the average normal stress developed at points A, B, and C. The diameter of each segment is indicated in the figure. 1 in. 0.5 in. 0.5 in. B. 3 kip A 9 kip 8 kip | c 2 kip Qs: The frame supports the loading shown. The pin at A has a diameter of 0.25 in. If it is subjected to double shear, determine the average shear stress in the pin. 2ft 2 ft 3 ft 600 Ib B
9 mm A .9 mm 96 mm 60 mm P 9 mm If the 9 mm hole is drilled through the plate determine the radius of the fillets such that the maximum stress value is the same for the hole %3D and the fillets for a applied force of P = 10 kN.
The beveled gear is subjected to the loads shown. Determine the stress components acting on the shaft at point B, and show the results on a volume element located at this point. The shaft has a diameter of 1 in. and can be modeled as if it is 200 lb. fixed to the wall at C. 12 in. 3 in. 25lb 75 lb
The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does not rotate while subjected to a force of 75 lb, determine the principal stresses on the cross section at point C.
Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with respect to the element shown. Sketch the results on the element. | 100 MPa 75 MPa 150 MPa
A thin hollow spherical container has a diameter 1 m and a thickness of 4 mm is subjected to an internal pressure. Determine the internal pressure the tensile stress of the element in the sphere is 500 kPa.
If L-719.01 mm, = 7839.63 N/m³, the normal stress σ caused by self-weight at the location of the maximum normal stress in the bar can be calculated as (Please select the correct value of σ given in Pa and rounded to three decimal places.) Select one: ○ 1. 1409.193 2. 845.516 O 3. 11273.545 ○ 4.8455.159 ○ 5.4509.418 6. 2818.386 7.5636.772
The steel bracket is used to connect the ends of two cables. If the applied force P = 1.50 kip, determine the maximum normal stress in the bracket. Assume the bracket is a rod having a diameter of 1.5 in.
The shaft shown below is made of AISI 1020 steel. Determine the most critical section, the principal stresses at the groove and at the fillet. Assume no concentration factors at the wall. The dimensions of the various diameters shown are d = 30 mm, D = 45 mm, and d2 = 40 mm. 40 mm. 7= 9mm 40 mm, 7 = 6 mm d 1 kN 40 mm 10 kN T= 50 N-m

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS