determine the radius of the fillets

Q: How many degrees are required if we taper a copper if it is measured .45 ft. as its taper per foot?…

A: Taper length, L= 0.45 ft= 0.45(12)= 5.4 in Larger end diameter, D1= 7.2 in Smaller end diameter, D2=…

Q: Fill in the blank which is given below Linear acceleration is equal to the product of and angular…

A:

Q: A compressor motor has a shaft diameter of 7⁄8 inch. The felt wiper that wrapstightly around the…

A: Given    Diameter,d = 7⁄8 inch.

Q: Determine the centroidal y-coordinate (in mm, round=off to 2 decimal places) of the plane curve…

A:

Q: Find the moment of inertia on the side 12 The answer is within an hour

A: It can be seen that that the coordinate axes are drawn and a vertical axis also drawn parallel to…

Q: w the components of F along the u and v w the triangle with sides and angles labeled to be able to…

A:

Q: The distance between the corresponding point on the screw thread when measured parallel to the axis…

A: Create:  It is the peak edge of a screw thread, that connects the adjacent flanks at the top. Flank:…

Q: Determine blank diameter?

A: Given; Height of the shell, h= 100 mmHeight with corner radius;  r=0.9 mmIt is poduced by cup…

Q: The rectangular plate has a semi-circle cut out as shown. The x' and y' axes go through the centroid…

A:

Q: A cylindral drill with radius 4 cm is used to bore a hole through the center of a sphere with radius…

A: Given Data⇒Radius of cylindrical drillr1=4 cmRadius of spherer2=7 cmProblem definition⇒Problem says…

Q: For the shape shown, calculating Q from the centroid to the top of the shape would yield the same…

A: The given statement is TRUE.

Q: Determine the centroidal y-coordinate (in inches, round=off to 2 decimal places) of the surface…

A: given figure to be find- centroidal Y coordinate

Q: Determine the angle made between the axes OA and AC.

A: The position vector of the point O with respect to point A is The position vector of the point C…

Q: y b a a = 9 in b = 1.2 in с 3 2.4 in

A: Find the centroid distance in inches.

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: calculate the hydraulic diameter of a two long flat plates with the measurement of 5 inches distance…

A:

Q: 2. Find the centroid of the figure shown. "20 in 18 in 10 in 12 in

A:

Q: A.7 Compute I, for the shaded area given that = 25.86 mm.

A:

Q: 250 Draw the triangle of for ces and determine the resul tant of the two forces acting in the…

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 45 45 y T 75 + Answers: 275 *…

A: To find location of centroid

Q: Write the equation of the Centroid of an area?

A: The centroid of an area is the center of gravity of that particular area where the entire mass can…

Q: Determine the centroidal x-coordinate (in inches, round=off to 2 decimal places) of the wire figure…

A:

Q: please solve the centroidal  Ixc, centroidal Iyc, Ix and Iy of the attached figures

A:

Q: Determine the diameter for the cylindrical cup

A: Given data; Neglecting the variation in the sheet thickness;  Determine the diameter ? Where,  10 mm…

Q: Find the resultant and angle of direction based on the horizontal. using tail to tip method 1. 20…

A:

Q: Find the mass of a cube of edge a, if the density varies as the sum of the distances from three…

A: Consider a cube of edge a, now it is given that, ρ=k(x+y+z)                 where, k is the…

Q: ratio of connecting rod length to crank radius.

A: Given; Consider the triangular forned by the connecting rodand the crank of an IC engine as two…

Q: Determine the distance of the center of mass of the bracket shown measured from the base. Use three…

A:

Q: 1 mm 10 mm 1 mm Y axis 5 mm 10 mm 1 mm X-axis

A:

Q: Determine the area of the shaded region. The value of b is 4 inches. Write the numerical value only.…

A:

Q: 30. 12ON

A:

Q: This composite shape is composed of a square, a half-circle, a triangle and a circular hole.…

A:

Q: Compute the volume generated by rotating the area shown through one revolution about the x-axis.

A: According to the given data A cross-sectional area is given  We need to find  Volume generated by…

Q: O Aveclar Af Length 10 units makes an angle. of 30 with avectorBofenoth 6units. Find the…

A:

Q: Determine blank diameter ?

A: Given data; Height with corner radius, r= 0.7 mmshell diameter,d =900 mmHeight, h=200 mmIt is…

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.