When filled to capacity, the unpressurized storage tank contains water to a height of h = 27 ft. The outside diameter of the tank is 8.2 ft and the wall thickness is 0.861 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.)

When filled to capacity, the unpressurized storage tank contains water to a height of h = 27 ft. The outside diameter of the tank is 8.2 ft and the wall thickness is 0.861 in. Determine the maximum normal stress and the absolute maximum shear stress on the outer surface of the tank at its base. (Weight density of water = 62.4 lb/ft³.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A locomotive semi-elliptical laminated spring has an overall length of 1 m and sustains a load of 70 kN at its center. The spring has 3 full length leaves and 15 graduated leaves with a central band of 100 mm width. All the leaves are to be stressed to 400 MPa, when fully loaded. The ratio of the total spring depth to that of width is 2. E = 210 kN/mm2. Determine the thickness and width of the leaves t = 11.64 mm & W = 109 mm t = 11.14 mm & W 103 mm O t = 11.94 mm & W = 118 mm O t = 11.34 mm & W = 108 mm t = 11.14 mm & W = 118 mm O
A vertical cylindrical steel tank 3 m in diameter and 6 m high has a wall thickness of 12 mm. If the stress is limited to 5 MPa, which of the following most nearly gives the maximum height of water up to which the tank may be filled? Select the correct response: 8.16 m 3.68 m 07.36 m 4.08 m
i need the answer quickly
A cross-section of a beam is shown in Figure Q2. If the shear force in this section is V = 281 KN, determine the value and the location of the maximum shear stress in the section. In Figure Q2, a = 72 mm and the origin of the coordinate system is at centroid of the cross section. Z A a AY 2a O 4a Figure Q2 J.L B 3a a
The cylindrical pressure vessel has an inner radius of 1.25 m and a wall thickness of 15 mm. It is made from steel plates that are welded along the 45° seam. Determine the normal and shear stress components along this seam if the vessel is subjected to an internal pressure of 8 MPa.
The beam is made from two plastic pieces glued together at the seam A. If it is subjected to the loading shown, determine the vertical shear force resisted by the flange of the beam at the critical section (in pounds). The supports at C and D exert only vertical reactions on the beam.
4. Determine the minimum thickness of the tank plating if the internal pressure is ODD: 1.3MPa EVEN: 1.7MPa and the allowable stress is 33MPa. 300mm 800mm
The ring, having the dimensions shown, is placed over a flexible membrane which is pumped up with a pressure p. Determine the change in the internal radius of the ring after this pressure is applied. The modulus of elasticity of the ring is E. What is the change in internal radius if p = 80 kPa, r = 20 mm, r₁ = 19 mm, and E = 200 GPa? ANS. 1.44 μm tri W
A steel cable having a diameter of 0.4 in. wraps over a drum and is used to lower an elevator having a weight of 800 lb. The elevator is 150 ft below the drum and is descending at the constant rate of 3 ft>s when the drum suddenly stops. Determine the maximum stress developed in the cable when this occurs. Est = 29(103) ksi, sY = 50 ksi.
The A-36 steel pipe is subjected to the axial loading of 60 kN. Determine the change in volume of the material after the load is applied.
Q2/ Determine the shear stress at points A and B on the beam if it is subjected to a shear force of V=400 kN. Represent the state of stress on a volume element of these points. 100 mm 100 mm 100 mm 100 mm 100 mm 100 mm R
Solve for the maximum permissible internal pressure of the cylindrical pressure vessel. (The answer should be in psi) Where: Inner radius= 24 inches Wall thickness= 0.25 inches Yield point of the material= 300 MPa Safety factor= 3.0 adequate