The bar has a constant width of 35 mm and a thickness of 10 mm. Determine the maximum average normal stress in the bar when it is subjected to the loading shown. 12 EN 22AN 35 mm

Q: The steel bracket is used to connect the ends of two cables. Y Part A O max = If the applied force P…

A: P=d=To determine:The maximum normal stress

Q: Determine the magnitude of the maximum shear stress on the stress element for which σx=-87 MPa,…

A:

Q: The internal loadings act on the section. Show the stresses with their directions that each of these…

A:

Q: The small steel plate is connected to the right angle bracket by a 6 mm diameter bolt and the…

A:

Q: ) If the load has a weight of 600 lb, determine the maximum normal stress developed on the cross…

A: An internal resisting force which is applied by the molecules of the object so that the shape of the…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: Determine the shear stress at point A and point B with appropriate units

A: Givendiameter of shaft d=80mmT=500Nm

Q: The steel shafts is made from two segments AB and BC, which are connected together using a fillet…

A:

Q: The beam is subjected to the loading shown. Determine the principal stress at point C.

A: Given data: The magnitude of the uniformly varying load is; ω = 8 kN/m. Evaluate the total load on…

Q: The beam supports the loading shown. Determine the state of stress at points E and F at section a-a.

A:

Q: If A and B are both made of wood and are 3 8 in. thick, determine to the nearest 14 in. the smallest…

A: Provided that both the elements A and B are 3/8 inch thick. The applied force of 800 lb will have…

Q: Determine the normal stress developed at points A and B. Neglect the weight of the block.

A: The sum of forces in the horizontal direction, ∑FX=-6 kips -12 kipsF=-18 kips The expression of the…

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: A wood pipe having an inner diameter of 3 ft is bound together using steel hoops each having a…

A: The cross sectional area of steel hoop is  The allowable stress of hoop is The diameter of wood pipe…

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: The solid circular rod has a cross-sectional area of 400 mm². It is subjected to a uniform axial…

A:

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Q: The steel bracket is used to connect the ends of two cables Part A O max If the applied force P= 1…

A: Given that,Applied force = P = 1 kipDiameter of rod of bracket = d = 2.25 inTo find:The maximum…

Q: Determine the principal stresses in the cantilevered beam at points A and B.

A: Draw sketch of beam and divide shear force into horizontal and vertical components.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.