Answered: At what temperature will the aluminum…

At what temperature will the aluminum and steel segments shown have stresses of equal magnitude after the 70-kip force is applied? Aluminum Steel

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

At what temperature will the aluminum and steel segments shown have stresses of equal magnitude after the 70-kip force is applied? Aluminum Steel A = 2 in.2 E = 10x 106 psi A = 3 in.2 E = 29 × 106 psi 70 kips 15 in. 10 in.-
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m B 5KN 0.6m AL 20KN What is the deformation &pE in mm? A=800 mm² A=1,200 mm²
A 26-foot-long structural steel bar is being tensed along its centroidal axis. Point B is being tensed by 180 kips of force and point C is being tensed by 121 kips of force. The bar has a rectangular cross-section with a height of 3.6 inches and width of 2.8 inches. The steel is HSLC steel with a yield stress, oy = 50 ksi and modulus of elasticity, E = 30,000 ksi. Show all work and any assumptions clearly. Record your answers on the answer key. Complete the following: ): Calculate the axial stress in sections AB and BC of the beam. Does the calculated stress in either section exceed the yield stress of the steel? Calculate the deformation in sections AB and BC of the beam. What is the total axial deformation that the beam experiences? What is the final length of the beam? Calculate the factor of safety that this structural bar was designed for. w = 2.8 in. A B 180 k C 121 k Answer Key σ > Gy Yes or No * 18 ft 8 ft Axial Section Stress (ksi) AB BC Total Deformation, 8 (in) Final Length…
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 6) What is the deformation &c in mm? 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m 10KN 0.8m 0.4m 5KN 0.6m What is the deformation 8Rc in mm? Al 20KN A=800 mm? A=1,200 mm²
two rods attached to a rigid bar AB with negligible mass . A 101 kN load was applied at the end of this bar. The computed stresses for steel and bronze are Blank 1 mPa and Blank 2 mPa respectively.
An aluminum rod is rigidly attached between a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximun value of P that will not exceed a stress in steel of 169Mpa, in aluminum of 98Mpa and in bronze of 111Mpa.
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 10KN 0.8m 0.4m 5KN 0.6m A 20KN 3) What is the deformation &cn in mm? A=800 mm? A=1,200 mm²
PROBLEM 1) An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D What is the axial stress o Ag in Pa? 10KN 0.8m 0.4m B 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
One of the following values is a possible for possion ratio for steel ? a. Zero b. one c. 0.3 d 0.9
A bar obtained by bonding together pieces of steel (Es = 29 x 106 psi) and brass (E = 15 x 106 psi) has the cross section shown (Fig. a). Determine the maximum stress in the steel and in the brass when the bar is in pure bending with a bending moment M = 40 kip-in. 0.4 in. 3 in. Brass 0.75 in. Steel Brass 0.4 in. (a) 1) Composite bar.
O Compute the maximum value of P that will not exceed a stress of bronze of 100 MPa. Bronze A=450 mm2 A=600 mm Aluminum Steel A=300 mm 2 Compute the max. value of P that will not exceed a stress of E-83 GPa E=70 GPs E=200 GPa aluminum of 90 MPa. 600 mm 1,000 mm 800 mm 3Compute the maximum value of P that will not exceed a stress of steel (3) of 140 MPa.