Answered: R14-7 The principal stresses at a point…

R14-7 The principal stresses at a point are shown in the figure. If the material is A36 steel, determine the principal strains. 84 MPa 140 MPa 6 MPa

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 6.3P: Compare the engineering and true secant elastic moduli for the natural rubber in Example Problem 6.2...

See similar textbooks

Related questions

Q: Axial Load, P(kN) A 2 m long axially loaded mild steel rod of 8 mm diameter exhibits the…

Q: A plate in equilibrium is subjected to uniform stresses along its edges with magnitude Oxx= 30 MPa…

A: Given data- A plate in equilibrium under uniform stress- σxx=30 MPa,σyy=30 MPa,σzz=0 MPa, Young's…

Q: At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is…

A: Initial temperature (Ti) = 60°F Bar-1: Width of bar1 = 3 in. Thickness of bar1 = 0.75 in. L1 = 32…

Q: Fc FA Fa Fc

A: According to given data Fa , Fb , Fc principal stresses are shown in three elements We need to…

Q: The figure shows the state of stress on the element at a point on a member. Determine the stress…

A: Normal stress about x axis, Normal stress about y axis, Shear stress, Angle, To find: Stress…

Q: 2. A steel with E = 29 000 ksi with a rectangular cross-section is bent over a rigid mandrel with R…

Q: At a temperature of 60°F, a 0.04-in. gap exists between the ends of the two bars shown. Bar (1) is…

A: Given Data Find the lowest temperature (T2) at which the two bars contact each other.

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 680 mm.…

A: FIND NA :y=36×95(952)-22×22(95-7-222)36×95-22×22y=22.637mmFIND MOI…

Q: Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

Question

R14-7 The principal stresses at a point are shown in the figure.
If the material is A36 steel, determine the principal strains.
84 MPa
140 MPa
6 MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

Estimate the elastic and plastic strain at the ultimate tensile strength in the low-carbon steel specimen in Figure 6.16.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
Narrow bars of aluminum are bonded to the two sides of a thick steel plate as shown. Initially, at T₁ = 70°F, all stresses are zero. Knowing that the temperature will be slowly raised to T₂ and then reduced to T₁, determine (a) the highest temperature T₂ that does not result in residual stresses, (b) the temperature T₂ that will result in a residual stress in the aluminum equal to 58 ksi. Assume aa = 12.8 x 10-6/°F for the aluminum and a = 6.5 × 10-6/°F for the steel. Further assume that the aluminum is elastoplastic with E = 10.9 × 106 psi and ay = 58 ksi. (Hint: Neglect the small stresses in the plate.) Fig. P2.121
Problem 1 An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Aluminum Steel A=800mm2 A=1000mm2 Bronze A=700mm? 4P 2P 500mm 600mm 700mm 1. What is the maximum value of P that will not exceed the axial stress bronze of 105 MPa? 2. What is the maximum value of P that will not exceed the axial stress in aluminum of 90 MPa? 3. If P=10KN, what is the axial force to be carried by the aluminum in KN? 4. If P is 5KN, what is the axial stress of steel?
The total tensile load of 160kN of a steel is to be stress at the middle portion limited to 150 N/mm2, find the diameter of the middle portion and also the length of the middle portion if the total elongation of the rod is to be 0.2mm. the length of the rod is 40 cm. consider the young modulus of a steel.
A steel with E = 29 000 ksi with a rectangular cross-section is bent over a rigid mandrel with R = 15 in as shown in the figure. If the maximum flexural stress in the bar is not to exceed the yield strength of 36 ksi, determine the allowable thickness h of the bar.
Calculate the stress and strain at each force interval. Plot a graph of the stress-strain curve. Estimate the yield point of the steel and note its location on the curve. Estimate the ultimate strength of the steel and note its location on the curve.
An aluminum bar carries the axial loads at the positions shown. If E=70GPA, compute the total deformation of the bar. Assume that the bar is suitably braced to prevent buckling. 0.4m D 1) What is the deformation 8Ag in mm? 10KN 0.8m 0.4m 5KN 0.6m 20KN A=800 mm? A=1,200 mm²
SITUATION. As shown in the figure below, a rigid bar with negligible mass is pinned at O and attached to two vertical rods. Assume that the rods were initially stress-free. Allowable stress in steel is 120 MPa and in bronze is 60 MPa. For this problem, a = 1.8m; b = 1.3m; c= 1.7m. a b I Steel: A 900 mm Bronze: A E 200 GPa E 83 GPa L-2.0m L=1.5m What is the value of P without exceeding the allowable stress of steel, in KN? 230 250 280 340 1200 mm
A beam made of titanium has a yield point of 800 MPa. The beam has 2 cm x 6 cm rectangular cross section and bends about an axis parallel to the 2-cm face. If the maximum bending stress is 600 MPa, find the corresponding bending moment.
Strain = 600 Stress = Strain = 500 Stress = 400 500 300 400 300 200 200 100 100 0.000 0.002 0.004 0.006 Strain 0.00 0.04 0.08 0.12 0.16 0.20 Strain Stress (MPa)
An aluminum alloy [E = 67 GPa; ν = 0.33; α = 23.0 × 10–6/°C] plate is subjected to a tensile load P. The plate has a depth of d = 225 mm, a cross-sectional area of A = 5100 mm2, and a length of L = 4.1 m. The initial longitudinal normal strain in the plate is zero. After load P is applied and the temperature of the plate has been increased by ΔT = 63°C, the longitudinal normal strain in the plate is found to be 2900 με. Determine: (a) the magnitude of load P. (b) the change in plate depth Δd.