An aluminum cable of length 5.0 m and diameter 10 mm is used to hang a load of 1000 kg. The modulus of elasticity of aluminum is 69 GPa and consider a Poisson's ratio of 0.30. What is the change in diameter when the load is applied? A 5.4 x106 m B) 25.4 x10-6 m 15.4 x106 m D 9.0 x106 m

An aluminum cable of length 5.0 m and diameter 10 mm is used to hang a load of 1000 kg. The modulus of elasticity of aluminum is 69 GPa and consider a Poisson's ratio of 0.30. What is the change in diameter when the load is applied? A 5.4 x106 m B) 25.4 x10-6 m 15.4 x106 m D 9.0 x106 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls 5 meters apart. The load on the rod is zero at 27 °C. E = 200 GPa, a = 11.25x106 m/m-°C. When the temperature rises to 57°C: a) What is the stress in the rod assuming that the walls are rigid. b) What is the stress in the rod if the walls spring together a total distance of o.5 mm.
Show all calculation and formula used: The second floor portion of a house is about to break down, so it was propped up by an iron column 4.0 meters long with cross sectional area of 30.0 cm^2. The iron column was compressed by 0.015 mm. How much load (N) the iron column is supporting? Y of iron = 19x10^10 Pa
1. The stress-strain diagram for a bar of steel alloy is shown. Determine: a) The modulus of Elasticity for the material b) The proportional limit c) The ultimate stress d) The modulus of resilience e) If the bar has a circular cross section with an initial diameter of 10-mm and is loaded to 260-Mpa, what will be the decrease in diameter under this load? Use v= 0.25 (MPa) Show complete solution.
Question 2 Consider the bar in figure 2, it has cross sectional area A 1.10-4m², modulus of elasticity E = = 200GPa, and length 1.5 m. The bar is fixed to a wall on its left hand side, and has a constant loading of 1(x) = −10 kN/m applied along its length. x=0.0 |(x) = -10 kN/m 1.5 m X x=1.5 Figure 2: diagram of bar subject to applied force along its length a) The displacement of the bar u(x) is governed by the equation ə du(x) AE dx dx +1(x) 0 x = [0, 1.5], state the two boundary conditions for this bar problem, and give a short reasoning for your answer (maximum 2 sentences for each boundary condition).
A rigid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that causes the point C to displace downward by 0.3 mm. Given: E (wire B) = 70 Gpa, E (wire C) = 200 Gpa and both wires have a diameter D = 4 mm. Consider a linear elastic behavior.
A. Explain briefly what you understand by the following terms I) strut II) column B. Distinguish between long and short column C)a hollow alloy 5000mm long with external and internal diameter of 50mm and 25mm respectively is used as a column with one end fixed and the other end hinged.Determine the buckling load by Euler's formula.Take Young modulus of elasticity as 180GN/m^2.
A long, rectangular bar (made of Material A) under a tensile load P hangs from a pin that is supported by two metal (made of Material B) posts. The Material A bar has a length of 2,0 m, a cross-sectional area of 5043 mm2 and a modulus of elasticity E=123 GPa. Each Material B metal post has a height of 0,3 m, a cross-sectional area of 4911 mm2, and a modulus of elasticity E=183 GPa. Calculate the maximum load P (in kN), if the displacement 6 is limited to 2,7 mm? Material B Post
Please don't provide handwritten solution.....
2. A core made of stainless steel (material 1, E, = 28 Msi) is fully bonded to an inner shell of brass (material 2, E, = 15 Msi), which is fully bonded to an outer shell of aluminum (material 3, Ea = 10 Msi). The rod is subjected to a compressive load, P = 50 kips. Determine: a) the normal stress in the brass and b) the deflection of the composite rod. Dimensions: L = 10 in, dı = 1 in, d2 = 2 in, d3 = 3 in. Recall that Msi =10° psi. Ans: ob = 7.76 ksi (C), ô = 5.176 x 10-³ in (shorter) 3 2 1 d, d d, - P
A slip collar with weight W = 150 pounds falls from a height h = 2 inch. Towards a flange located at the bottom of a vertical slender bar. The bar has a length L = 4 feet and a section area transversal A = 0.75 in2 and its modulus of elasticity is E = 30 x 106 psi. Calculate the following amounts: a) the maximum downward displacement of the flange b) The maximum tensile stress in the bar c) The impact factor.
A solid circular brass rod is subjected to a compressive axial load of P = 120 kN. The diameter of the rod is d = 30 mm, and its length is L = 1000 mm. After load P is applied, the contraction of the rod is ō = 36 mm, and its diameter becomes d' = 30.360 mm. What is the modulus of elasticity for this material? P L P
True one