3. A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls5 meters apart. The load on the rod is zero at 27 °C. E = 200 GPa, a = 11.25x106 m/m-°C. Whenthe temperature rises to 57°C:a) What is the stress in the rod assuming that the walls are rigid.b) What is the stress in the rod if the walls spring together a total distance of o.5 mm.

Answered: Image /qna-images/answer/afe7599f-72d1-49aa-ad16-7cc08d4492f3.jpg

3. A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls 5 meters apart. The load on the rod is zero at 27 °C. E = 200 GPa, a = 11.25x10“ m/m-°C. When the temperature rises to 57°C: a) What is the stress in the rod assuming that the walls are rigid. b) What is the stress in the rod if the walls spring together a total distance of o.5 mm.

3. A 5-m rod having a uniform cross-sectional area of 1000 sq.mm. is secured between two walls 5 meters apart. The load on the rod is zero at 27 °C. E = 200 GPa, a = 11.25x10“ m/m-°C. When the temperature rises to 57°C: a) What is the stress in the rod assuming that the walls are rigid. b) What is the stress in the rod if the walls spring together a total distance of o.5 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical rod of diameter 23 mm and length 234 mm is subjected to a tensile load of 57 kN and it elongates to 0.5 mm. Find Young's Modulus (Modulus of Elasticity). Solution: i) Cross-section Area, A = ii) Stress = iii) Strain = iv) Young's Modulus =
Q1B
The structure consists of two bars. Axial loads 40 kN and 10 kN are loaded as shown in Figure B. Determine: a) Global stiffness matrix b) Nodal displacement c) Stress in each bar Table 2 Steel Aluminium Brass Area 400 350 350 (mm³) E(Gpa) 200 70 83 Aluminum Brass Steel 40 kN - 10 kN L 500 mm 400 mm 300 mm
A steel (E=210 GPa, v=0.32) cylindrical vessel has a diameter R= 25 cm, thickness t=0.2 cm and length L=100 cm. What is the increase in the length of this vessel if it is subject to PR PR. an internal pressure P kPa (unit in kPa)? (Remember: o, =
Q2/ A force P = 1 KN applied to a right bar suspended by three wires, as shown below. all wires are of equal size and the same material. for each wire, A = 80 mm , E =200 GPa , and L =4 m. If initially, there were no slack in the wires, how will the applied load distribute between the wires? 200 100 100 4000 mm mm mm mm
Q1 ]: Two solid rods (1) and (2) of the same material are joined together at flange B and loaded as shown in Fig. Q1. If the normal stress in each rod must be limited to 275 MN/m². (a) find the minimum diameter required for each rod. (b) if the L₁ = 115 mm and L₂ = 105 mm, compute the total deformation of the rod, the modulus of elasticity E = 60 GN/m². Fig. Q1 Stepped Bar 130 kN 65 kN A -d₁ 130 kN B C -d₂
A slip collar with weight W = 150 pounds falls from a height h = 2 inch. Towards a flange located at the bottom of a vertical slender bar. The bar has a length L = 4 feet and a section area transversal A = 0.75 in2 and its modulus of elasticity is E = 30 x 106 psi. Calculate the following amounts: a) the maximum downward displacement of the flange b) The maximum tensile stress in the bar c) The impact factor.
Q1// A hollow shaft of 10mm inside diameter and 5mm thick and 2m long extends by 0.5 cm under a tensile load (P) .find 1- the load P if E=2.10° N/cm? 2-the tensile stress in the shaft.
1.Calculate the axial force in rope J in N. 2.Calculate the elongation in rope K in mm. 3.Calculate the normal stress in rope L in MPa.
The frame in the figure is made of bars that have a square (solid) cross section of 3 cm on each side. A load of 5 kN is applied to the reinforcement. a) Draw the FBD of the reinforcement indicating the forces in each bar b) Calculate the stresses in each bar (don't forget to indicate if these are compressive stress or tension) c) Calculate the deflection of the bar AB if it were made of steel with E = 200 GPa