The link shown, made of steel with y-410MPa and E-200GPa is subjected to a tensile load of 30kN. Let (h=6b). Assume the factor of safety is 2. a) Determine the dimensions of the section with the design based on yield strength. b) If this link, which is 40cm long, must not elongate more than 0.12mm, what should be the dimensions of the cross section? L F F -h b

The link shown, made of steel with y-410MPa and E-200GPa is subjected to a tensile load of 30kN. Let (h=6b). Assume the factor of safety is 2. a) Determine the dimensions of the section with the design based on yield strength. b) If this link, which is 40cm long, must not elongate more than 0.12mm, what should be the dimensions of the cross section? L F F -h b

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Civil Engineering
N for Newton, m for meter, mm for millimeter, N/(mm^2) for Stress, mm^2 or m^2 for Area, mm^4 for Moment of inertia and Nm for bending moment. Use brackets if the power is MINUS for Example: 0.00125 N =1.25*10^(-3)N. A member is formed by connecting two steel bars shown below. Assuming that the bars are prevented from buckling sideways, calculate the magnitude force "P" that will cause the total length of the member to decrease 0.56 mm the values of elastic modulus for steel is 215 MPa. Take H1 = 4 cm, H2 = 9 cm, top bar (R) is 3 x 3 cm and bottom bar (Q) is 5 x 5 cm. Also, determine the stress-induced in each section of the bar. Solution: i) Magnitude Force, P = ii) Stress-induced in the top bar = iii) Stress-induced in the bottom bar =
Question 5 A lead of 5kN is to be raised using a steel wire. Find the minimum diameter of the wire required to raise the load if the yield stress of steel is 300MPA. i= Ø 5kN
3. If P= 100KN, Compute the total deformation. 112 in 201 60 CM 90 cm 9p 4P 7P $=2ch $=6m 644ch E= 120 GPa E = 200 GPa = 100 GPO
The shaft is pulled by force F. Shaft The yield strength of the material is 500 MPa and the factor of safety is 2 Spindle length 1 m Size the shaft as the outer diameter / inner diameter ratio is 1.5 Note:show the calculations in detail
Please help me thanks!
A steel rod with length equal to 12 ft, has a diameter of 0.8 inches in quarter of its length and a diameter of 0.4 inches the rest. If it is subjected to a tensile load of 6,500 lbs, what will be the total deformation of the bar if it has a modulus of elasticity E = 29.5 10^6 psi.
please explain in neat hand writing so I can undertstand
Please don't provide handwritten solution.....
E. Rigid bar AD is horizontal before the weight of 112 lb is applied to the end of wire BC at C. The wires have a radius of 0.025" and are made of A913 steel. Determine the rotation of AD and how far C will move down due to application of the weight See Appendix of text for any material properties needed. Ans: 0.00071 radians 3 ft - 2 ft -3 ft- D B 4 ft W
2. A core made of stainless steel (material 1, E, = 28 Msi) is fully bonded to an inner shell of brass (material 2, E, = 15 Msi), which is fully bonded to an outer shell of aluminum (material 3, Ea = 10 Msi). The rod is subjected to a compressive load, P = 50 kips. Determine: a) the normal stress in the brass and b) the deflection of the composite rod. Dimensions: L = 10 in, dı = 1 in, d2 = 2 in, d3 = 3 in. Recall that Msi =10° psi. Ans: ob = 7.76 ksi (C), ô = 5.176 x 10-³ in (shorter) 3 2 1 d, d d, - P
4. Show your complete solution.