Consider two types of a column cross-section: a hollow square and a hollow circular section. In bothcases the wall thickness is 6 mm and the area occupied by the load-bearing material is 965 mm². Findwhich of these two column types produces a better buckling performance with relevant calculationssupporting your answer.AnswerThe outer size of the hollow square section can be calculated asmm• The outer diameter of the hollow circular section can be calcualted as.mmThe second moment of area for the hollow square section can be calculated asmmThe second moment of area for the hollow circle section can be calculated asmmFind which of these two column types produces a better buckling performance.O Hollow Circular Section O Hollow Square Section

Answered: Image /qna-images/answer/f1dca327-3832-44d4-ab0f-d2473d453c09.jpg

Consider two types of a column cross-section: a hollow square and a hollow circular section. In both cases the wall thickness is 6 mm and the area occupied by the load-bearing material is 965 mm². Find which of these two column types produces a better buckling performance with relevant calculations supporting your answer. Answer The outer size of the hollow square section can be calcaulated as mm The outer diameter of the hollow circular section can be calcualted as mm The second moment of area for the hollow square section can be calculated as mmª

Consider two types of a column cross-section: a hollow square and a hollow circular section. In both cases the wall thickness is 6 mm and the area occupied by the load-bearing material is 965 mm². Find which of these two column types produces a better buckling performance with relevant calculations supporting your answer. Answer The outer size of the hollow square section can be calcaulated as mm The outer diameter of the hollow circular section can be calcualted as mm The second moment of area for the hollow square section can be calculated as mmª

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

There is a gap of δ = 0.05cm between the steel and copper bars seen in the figure. i) When the ambient temperature rises to 200oC, will there be a reaction force in the bearings? ii) If there is a reaction force, calculate the reaction forces RA and RB at points A and B. The cross-sectional area of both bars is equal and 5cm ^ 2. Materials;Modules of Elasticity: E Steel = 210 GPa E Copper = 120 GPa Expansion Coefficients: α Steel = 12.10-6 1 / 0C α Copper = 16.10-6 1 / 0C
1. A rigid horizontal bar of negligible mass is connected to two rods as shown in the figure. If the load P = 10 kN. determine the following: (1) the vertical movement on the bronze, mm (2) the vertical movement on the steel, mm (3) the vertical movement at P. Figure Steel 2m A = 900 mm? E = 200 GPa 3m 3m www I 2m> 1m Bronze A = 1200 mm? 2m E = 83 GPa P = 10 kN ww.
The stepped and surface-ground steel bar in the figure is subjected to a bending moment varying between Mz=100 Nm and Mz=250 Nm and a torsional moment varying between Tx=80 Nm and Tx=320 Nm in opposite directions. The tensile strength of the rod material is Sut=800 MPa and it works under room conditions. For 50 percent reliability, check the fatigue safety of the rod.
25 A hot rolled steel shaft of circular cross-section is subjected to a load that varies from -F to +4F as shown in the below figure. The length of the beam is 142 mm and it has a diameter of 24 mm. Determine the maximum load that the given beam material can withstand for an indefinite life with a factor of safety 1.3. The fatigue stress concentration factor is 1.32. Assume the following values: Yield strength = 435 MN/mm2, endurance stress =280 MN/mm2, ultimate strength = 570 MN/mm2, size factor = 0.84, surface finish factor = %3D 0.89. Use Soderberg relation in your design. Also calculate the mean stress in N/mm2. -F d 4F
A cantilever beam of circular cross-section is made of alloy steel is subjected to a fluctuating load that varies from -F to 2F. Determine the minimum ultimate strength of the beam material which can withstand the fluctuating loads. The variable forces on the beam induce corresponding fluctuating stresses between + 48 N/mm2 to -24 N/mm?. Assume the following values. Yield strength = 0.55 ultimate strength, endurance stress = 0.45 ultimate strength. Take a factor of safety = 2. Use Soderberg relation in your design i) Calculate mean and alternating stress ii) Calculate endurance strength **Note: Please upload your handwritten working/solution to the link provided. Mean Stress in N/mm^2 ... Variable Stress in N/mm^2 ... Endurance Strength in N/mm^2 .. Ultimate Strength in N/mm^2..
The stress-strain plot of the polyester resin material is given in the figure. The AC beam is supported by the AB rod and CD column made of this material and is subjected to a single load of P = 80 kN. As the diameter of AB rod is 40mm and diameter of CD column is 80mm(a) What is the modulus of elasticity? Calculate the elasticity coefficient of the material whose stress-strain graph is given.(b) Find the slope of the AC rod after loading.
Consider the steel truss and member cross-section presented in figures below. All the members of the truss have the same cross-section as shown in the figure to the right. They all also have a Young's Modulus of 210 GPa. What can the highest value of force F be before member AC fails by buckling? Force 1AN - 300 mm 40° 4 m $35 mm 7m 300 mm 8 m 35 mm 35 mm 35 mm Please provide your answer in kN.
A torsional moment T = 8,019 Nm and a load P = 39,980 N are applied at the same time to a circular hollow shaft of unknown length L, as shown in Figure Q8. The load P is applied in the centre of the shaft's circular cross-sectional area. The shaft has an inner diameter d = 38 mm and an outer diameter D = 90 mm. Point A in Figure Q8 is on the outer surface of the shaft. Figure 8 Calculate the maximum principal stress at point A. Use π = 3.14159 if needed. Calculate your answer in the unit: mega-Pascal (MPa). Report you answer to 3 decimal places.
Derive the Euler Buckling formula for column having fixed support at both ends. (eXPLAIN IN DETAIL IN HAND WRITTEN )
Figure 2 shows an assembly made of a steel tube of internal and external diameter of 20 mm and 30 mm respectively, brass and copper bars, each having 25 mm of diameter. The three materials have equal length of 500 mm and are symmetrically rigidly fixed at the upper end while being joined by a horizontal collar (with negligible mass) at their bottom end. An application of a vertical downward load P on the assembly, results in storing a total of 20 J of energy. Brass Copper Steel Collar Figure 2: A system of steel tube, brass and copper bars The moduli of elasticity for steel, brass and copper materials are Es=200 GPa, EB=100 GPa and Ecu=80 GPa, respectively. Calculate: 2.1. The load P if it is applied gradually 2.2. The load P if it is applied suddenly 2.3. The impact load P that falls from a height of 200 mm above the collar.
Find the correct solution for the given question,ASAP