A long, rectangular bar (made of Material A) under a tensile load P hangs from a pin that is supported by two metal (made of Material B) posts. The Material A bar has a length of 2,0 m, a cross-sectional area of 5043 mm2 and a modulus of elasticity E=123 GPa. Each Material B metal post has a height of 0,3 m, a cross-sectional area of 4911 mm2, and a modulus of elasticity E=183 GPa. Calculate the maximum load P (in kN), if the displacement 6 is limited to 2,7 mm? Material B Post

A long, rectangular bar (made of Material A) under a tensile load P hangs from a pin that is supported by two metal (made of Material B) posts. The Material A bar has a length of 2,0 m, a cross-sectional area of 5043 mm2 and a modulus of elasticity E=123 GPa. Each Material B metal post has a height of 0,3 m, a cross-sectional area of 4911 mm2, and a modulus of elasticity E=183 GPa. Calculate the maximum load P (in kN), if the displacement 6 is limited to 2,7 mm? Material B Post

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

QI A rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and C.The cable at B has nominal diameter D=12 mm and the cable at C has nominal diameter D= 20 mm. IF a load P=30 -dc KN acts at end D of the bar. What is the stresses for the cables at B and C if the temperature rises by 60°C. (E = 140 GPa and a=12 x 10/°C for both cables). -26 to -26- P
Question 2 Consider the bar in figure 2, it has cross sectional area A 1.10-4m², modulus of elasticity E = = 200GPa, and length 1.5 m. The bar is fixed to a wall on its left hand side, and has a constant loading of 1(x) = −10 kN/m applied along its length. x=0.0 |(x) = -10 kN/m 1.5 m X x=1.5 Figure 2: diagram of bar subject to applied force along its length a) The displacement of the bar u(x) is governed by the equation ə du(x) AE dx dx +1(x) 0 x = [0, 1.5], state the two boundary conditions for this bar problem, and give a short reasoning for your answer (maximum 2 sentences for each boundary condition).
The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross- sectional area of the wire is 1.75 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. D 90 cm 90 cm B 180 cm Ale 120 cm
The blue bar is made from steel with the following mechanical properties: Young's Modulus, E = 17x10° psi; Poisson's Ratio v = 0.31. The bar has a circular cross-section with diameter d= 0.50 in. being the length of each side. 557 lb 557 Ib 60 in. - Determine the following under the action of the axial load (assume elastic behavior): a. The bar's axial deformation, ô, in in.: b. The average axial or longitudinal strain, ELong: c. The change in the bar's diameter, in in.:
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm
An aluminium hollow box column of square cross section is fixed at the base and free at the top. The width of each side is b=150 mm and the thickness t=10 mm. A compressive load P = 160 kN acts on the outer edge of the column at the midpoint of the side as denoted by P. What is the longest permissible length L of the column if the stress is not to exceed 100 MPa? (E = 70 GPa) b Section 4-A
A vertical load P is applied at the center B of the upper section of a homogeneous frustum of a circular cone of length L, minimum radius rB, and maximum radius rA, as shown in the figure below. It is made of a material with a modulus of elasticity E. Neglect the effect of its weight. Use the following values: rA = 2 in, rB = 0.5 in, L = 3 ft, E = 30 (103 ) ksi, and P = 1800 lbf. Discretize the original geometry into three equal-length finite elements and (a) Compute all the nodal displacements. (b) Compute all the element axial stresses. (c) Plot the displacement field from the finite element method solution. (d) Plot the axial stress field from the finite element method solution.
A solid circular brass rod is subjected to a compressive axial load of P = 120 kN. The diameter of the rod is d = 30 mm, and its length is L = 1000 mm. After load P is applied, the contraction of the rod is ō = 36 mm, and its diameter becomes d' = 30.360 mm. What is the modulus of elasticity for this material? P L P
1. The rigid beam ABC is supported by the pin joint at A and the steel wire BD. The wire is 0.10 inches in diameter and 90 inches long before the load is applied. Find the stress in the wire, the change in length of the wire when the load is applied, and the diameter of the wire under the load. Use E = 30 X 106 psi and v = 0.35. ܢܢܢܢܢܢ A 60 in 120 in D B C 750 lb
A steel bar 40 mm x 40 mm square cross-section is subjected to an axial compressive load of 200 kN. If the length of the bar is 2 m and E= 200 GPa, the elongation of the bar will be (a) 1.25 mm (b) 2.70 mm (c) 4.05 mm (d) 5.40 mm e) none of these