A wooden beam is fabricated from three pieces of lumber to form the I-beam cross section shown. The flanges of the beam are fastened to the web with nails that can safely transmit a force of 100 lb in direct shear. If the beam is simply supported and carries a vertical 1305-lb load at the center of a 12-ft span, determine the maximum spacing s (along the length of the beam) allowed for the nails. 4 in. 2 in. 2 in. 8 in. 2 in. Nails O 1.57 in. O 2.05 in. O 1.16 in. O 1.88 in. O 2.40 in.

A wooden beam is fabricated from three pieces of lumber to form the I-beam cross section shown. The flanges of the beam are fastened to the web with nails that can safely transmit a force of 100 lb in direct shear. If the beam is simply supported and carries a vertical 1305-lb load at the center of a 12-ft span, determine the maximum spacing s (along the length of the beam) allowed for the nails. 4 in. 2 in. 2 in. 8 in. 2 in. Nails O 1.57 in. O 2.05 in. O 1.16 in. O 1.88 in. O 2.40 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A reinforced concrete T-beam contains 1.25x10 m² of steel reinforcement on the tension side. If the steel stress is limited to 115 MN/m² and the concrete stress to 6.5 MN/m², estimate the permissible bending moment. The modular ratio is 15. 30 cm- 12 (0.30-m -60 cm- 10cm -000-1.25 x 10³m² 15cm
. A beam is constructed from a reinforced 50mm x 200mm section of timber using two L120x80x12 steel angle sections. Considering that the effort allowable stress in wood is 10 MPa, and the allowable stress in steel is 110 MPa. Determine the maximum positive and negative moment that the beam can support
Design Shear ReinForcement For a beam Shown below. It's Size is 350 x 600· It's effective depth is 525mm. It is Supported
The cross section of the beam is made with a 6"x6" plank of wood and reinforced with another 2"x6" as shown in the figure. Determine what forces are exerted on each of the nails shown in the section spaced every 6", when a force P= 500 [lb] is applied at the center of the beam.
Q2/ Determine the amount of steel required to create a balanced condition for the beam that has height 500 mm, width 300 mm, effective depth (d) 450 mm as shown in figure 2, where f'c 25 MPa and fy = 400 MPa. (50 marks) %3D 300 mm 500 mm Figure 2
A composite beam is fabricated by bolting two 3.6-in.-wide by 13-in.-deep timber planks to the sides of a 0.5-in. by 13-in. steel plate. The moduli of elasticity of the timber and the steel are 1700 ksi and 29000 ksi, respectively. The simply supported beam spans a distance of 25 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD = 7 ft, LBc = 11 ft, b = 3.6 in., d = 13 in. and t = 0.5 in. (a) Determine the maximum bending stresses o,,o, produced in the timber planks and the steel plate if P = 3.7 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1010 psi and 26800 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: LAB (a) o, = (b) P = i i B LBC b F لالها b Cross section C kips. d ksi, o, = LCD D ksi.
I need the answer as soon as possible
Work out the quantity of steel in a 5m long simply supported beam of size 150 X 400mm overall. Bottom bar: 4- 10mm diameter straight bars. Anchor bar: 2-08mm diameter straight bars, stirrups 8min diameter @ 150mm cic throughout the length of the beam. Clear cover as 10mm on all sides.
a) Write and explain one advantage and onedisadvantage of using intermediate stiffeners in plate girders. b) If a plate girder design was initially determined to require intermediate stiffeners, but one optedtonot use them, how else could the plate girder be designed to achieve the same shaer capacity. c) A w-shepe beam is bent in bi-axial bending. All loading passes through its shear center. Please explain why the flexural strenght about its weak axis is the fullplastic moment capacity regardless of Lb
Current Attempt in Progress A composite beam is fabricated by bolting two 2.4-in.-wide by 10-in.-deep timber planks to the sides of a 0.6-in. by 10-in. steel plate. The moduli of elasticity of the timber and the steel are 1790 ksi and 28300 ksi, respectively. The simply supported beam spans a distance of 18 ft and carries two concentrated loads P, which are applied as shown. Assume LAB = LCD= 4 ft, LBc = 10 ft, b = 2.4 in., d = 10 in. and t = 0.6 in. (a) Determine the maximum bending stresses o,, o, produced in the timber planks and the steel plate if P = 3.4 kips. (b) Assume that the allowable bending stresses of the timber and the steel are 1450 psi and 25000 psi, respectively. Determine the largest acceptable magnitude for concentrated loads P. (You may neglect the weight of the beam in your calculations.) Answers: (a) o, = (b) P= LAB i i B LBC F Lodlod b Cross section C kips. d ksi, o, = LCD D ksi.
Calculate Euler buckling strength for a steel beam web of ISMB 400 @ 604.3 N/m. Given that non dimensional effective slenderness ratio = 1.075 ISMB 900@ 600.3 N/m Effective depth of web = 340 mm Thickness of web (t) = 8.9 mm
Problem 4: Two wooden members shown which support a 4.5kip load, are joined by plywood splices fully glued on the surfaces in contact. The ultimate shearing stress in the glue is 360psi and the clearance between members is 1/4in. Determine the required length L of each splice if a factor of safety of 2.75 is to be achieved. 4.5kips 4 in 4.5kips