Work out the quantity of steel in a 5m long simply supported beam of size 150 X 400mm overall. Bottom bar: 4- 10mm diameter straight bars. Anchor bar: 2-08mm diameter straight bars, stirrups 8min diameter @ 150mm cic throughout the length of the beam. Clear cover as 10mm on all sides.

Q: Directions: Check the safety of the typical reinforced concrete tee beam used to support the…

A:

Q: 5. Using method of sections, determine whether the following are in tension or compression: FH GH GI…

A:

Q: Explain a bernullies beam with equation(s)

A: Bernoulli's beam, also known as the Euler-Bernoulli beam, is a concept in structural engineering…

Q: The shown is a beam-column connection. Assuming normal weight concrete, f'c = 5000 psi, fy = 60 ksi…

A:

Q: te t for Tension and C for Compression). ]12 kN 4 m B 6 kN 4 m C E I K 6 @ 3 m

A:

Q: All columns and girders are A992 steel.

A: Given: The columns are oriented in the frame such that the x axis is out of plane and y axis is in…

Q: A truss heel joint similar to that in Figure 7.5 is made with3∕4-in. plywood and 10d nails. Find the…

A: Using the table of reference: The lateral load value is 105 lb.

Q: Given: Consider the floor frame below supports a 6-in. concrete floor. Assume the beams and girders…

A:

Q: Which of the following best gives the purlin load wuy? See loaded purlin. The figure shown has…

A: Answer  Roof slope (θ): tanθ = 12 θ = 26.565 degree Based on the given data, draw the tributary…

Q: Mx=20 kip, section made of two 3x10", one 0.5 x 10 QUESTIVI Calculate the The maximum normal stress…

A: Given A composite beam Required  Maximum normal stress in steel

Q: Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded…

A: A loaded beam is given and it has been asked to determine location of maximum flexural compressive…

Q: "D.77. Compute the ultimate strength capacity of the positive moment beam design below. f'c= 21 MPa,…

A:

Q: Trusses and Frames (Method of Joints, Sections, Member) Determine the magnitude of the force (in kN)…

A: The truss shown in the above figure. We have to find out the magnitude of the force (in kN) in…

Q: 4. The structure shown is hinged at A and C. Find the horizontal and vertical components of the pin…

A:

Q: Which joint would be the best place to start your analysis of the truss shown?

A:

Q: Draw the Free Body Diagram for the structure below. 3'-0" A7 Pin support 800 lb 5' 0" 60⁰ 500 lb…

A:

Q: 1. Identify zero force memeber. (Draw the FBD of Joint contain zero force member) B H|100 kN 60 kN K…

A: Identify the zero force member (Draw the FBD of joint contain zero force member).

Q: - Deteimine th veactions at the supports (pin B Por the beam baded as shown in the figure " .-. 0.2m…

A:

Q: Determine the force in each member of the truss illustrated below. В 3m A E H -* 3m le F 3m 3m 3m 25…

A:

Q: What is the required diameter of sag rods in mm? Considering sag rods and tie rods at midspan…

A:

Q: 1006. Determine the width b of the 10-mm steel plate fastened to the bottom of the beam in Problem…

A:

Q: determine the zero force members explain please

A: Conditions for zero force members: If at a joint only two members meet and there is no external…

Q: Please show clear and complete solutions. Box the final answers. A₂ M A, M Answer: ly = 10' L A L B…

A:

Q: For the truss shown below identify zero force members. Make sure to state which joint you are…

A:

Q: Determine the forces in each member of the truss. State wether it is in tension or compression. Draw…

A: Given: A simply supported truss with hinge support at A and roller support at B. To find: Forces on…

Q: HiW@ Draw SitiD and BM.n for beam S hown by graphlal methds Ans/ yW/m Veny = 4 W, Vioy =-3 W hinge…

A:

Q: Design the flexural reinforcement of the cantilever beam shown below for the given loading and data.…

A: Solution: Design Bending Moment and Shear Force: Design Load = 1.2DL+1.6 LL=1.2(100)+1.6(70)=232kN…

Q: The beam shown is constructed by joining two pieces of wood together using screws. If the resistant…

A: Given:- A beam is constructed by joining two pieces of wood together using screws The resistant…

Q: C. Determine the area of reinforcing steel required for the isolated T beam shown it f'=30 MPa, fy =…

A: Answer Let us first calculate the Nominal Moment capacity required Mn = Muϕ Mu = 1100 Kn-m  ϕ = 0.9…

Q: 50 kN 50 kN 100 kN Sm 4m 3m From the given truss, which member has an internal force of 50 kN…

A: A loaded truss in given and it has been asked to determine a member which is carrying 50KN…

Q: Determine the forces in all the members, and state if these members are in tension or compression.…

A: Given data  Span length  Vertical loading  Horizontal loading.    At joint D only two members are…

Q: Height h=584.6 mm What is the shear resistance of a universal beam (UB) with the following…

A:

Q: Determine the forces BG, DF & BC of the truss using method of joints. 80 k 80 k 20k 8ft 80 k 80 k 8t…

A:

Q: Please answwer the question in the picture, Show all of your work please.

A: Follow the steps...Image_1Image_2Image_3As calculated above Absolute Maximum SF =17 kipAbsolute…

Q: uired information TE: This is a multi-part question. Once an answer i owe scissors roof truss is…

A:

Q: Trace the load, draw FBD and calculate support reactions for the following elements: Beam B2 Beam…

A:

Q: A D E 1.H Section 2. Wide-Flange 3. American Standard 4. Unequal Leg Angle 5. C Section 6.T Section…

A: Matching the cross section

Q: : The continuous beam shown in figure below ha a positive reinforcement consists of (4#19 bars)…

A: Consider the cross-sectional layout of the beam Calculate the factored load on the beam

Q: OPEN- 141 ロ 14' ZG1 イー w=40psf っ? 20 12 ロ

A: given data load=40psflength of beam L=44fttributary width w=42ftarea A=44×42=1848ft2distrubuted load…