The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?

The service load bending moments on a beam are 128 kip-ft for dead load and 107 kip-ft for live load. The beam is 12 in. wide, f'c is 3000 psi and fy is 60 ksi. Determine Mu. Mt. p. R. the depth of the beam and the As of tensile reinforcing required. How many no. 8 bars or No. 10 bars would have the required As?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using the method of consistent deformation, determine the axial force in all the members of the truss shown in EA = constant. B A L (a) Actual truss C D P L
Please Answer the problem attached image. ASAP Thank you very much.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P = 19 kips, w = 2.0 kips/ft, LAB = 3.4 ft, LBc = 3.4 ft, and LCD 15.6 ft. Determine the magnitude of the maximum bending stress in the beam. = P ksi Answer: Omax i B LAB LBC = C W LCD D X
Use AISC Equation E3-2 or E3-3 and determine the nominal axial compressive strength for the following cases: a. L= 10 ft b. L= 30 ft
Compute the nominal compressive strength of the member shown in Figure . Use AISC Equation E3-2 or E3-3.
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm
AW18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P= 20 kips, w = 5.8 kips/ft, LAB = 4.0 ft, LBc = 4.0 ft, and LcD = 13.0 ft. Determine the magnitude of the maximum bending stress in the beam. A В C D LAB LBC LCD Answer: Omax i ksi
Direct Stress Bronze Aluminum Steel A = 0.75 in.2 A = 1.0 in.? A = 0.5 in.? 3P 2F P 4P- -3 ft→ 5 ft 4 ft- 2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for bronze.
A flexural member is fabricated from two flange plates 1/2 x 16 and a web plate 1/4 x 20. The yield stress of the steel is 50 ksi.
1. For the cantilever beam shown below the required area of steel is 2.12 in?. 3 #8 bars are used. The end of each bar includes a standard 90 degree hook that is terminated at 2.5 in. from the outside face of the supporting column. Is the anchorage length sufficient to fully develop the tensile strength of each of the steel bars?Assumptios are as follows: fe = 4000 psi ; fy = 60000 psi ; uncoated coated bars ; light weight concrete; Sufficient stirrups provided 1.93 3#8 3#8 |2,5" 12" 12"
A W18 × 40 standard steel shape is used to support the loads shown on the beam. Assume P = 30 kips, w = 3.4 kips/ft, LAB = 4.2 ft, LBC = 4.2 ft, and LCD = 14.8 ft. Determine the magnitude of the maximum bending stress in the beam.
AW18 x 40 standard steel shape is used to support the loads shown on the beam. Assume P= 27 kips, w = 5.0 kips/ft, LAB = 3.6 ft, LBC= 3.6 ft, and Lcp = 14.4 ft. Determine the magnitude of the maximum bending stress in the beam. P LAB Answer: Omax C B LBC |C ksi W LCD X