1. built up timber-beam is subjected to a vertical shear of 5 kN. Knowing that the allowable shearing force in each nail is 300 N, Which nearly gives the largest permissible spacing of the nails in mm. EI 50 mm 250 50 mm 50 mm 50 mm 50 mm

1. built up timber-beam is subjected to a vertical shear of 5 kN. Knowing that the allowable shearing force in each nail is 300 N, Which nearly gives the largest permissible spacing of the nails in mm. EI 50 mm 250 50 mm 50 mm 50 mm 50 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Example 2: At a cross section in a T-beam with flange width b= 600 mm, effective depth d=375 mm,…

Q: The nails are on both sides of the beam and each can resist a shear of F. If the beam is subjected…

A: as we can know that maximum shear will occur at AB of a vlaues V(max)=(P+4.5)KN

Q: At a cross section in a rectangular beam with b=300 mm and d=500 mm, flexural reinforcement is 5T20.…

Q: d Craked Section 1. A doubly reinforced beam ha

Q: A simply supported beam has uniform load span of 6.0m. It carries maximum shear force of 125 kN at…

Q: Question 7 A simply supported beam made of timber is shown; determine the minimum required width b,…

Q: A 16 ??–diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the…

Q: A horizontal tension member is to be constructed of two pieces of plastic glued along the incline pq…

Q: A truss heel joint similar to that in Figure 7.5 is made with3∕4-in. plywood and 10d nails. Find the…

A: Using the table of reference: The lateral load value is 105 lb.

Q: Problem. Calculate the shearing strength of the section shown below at 5 ft from the right support…

A: Given data, Area of steel = 2.0 in² Effective force = 150 kips Compressive strength of concrete =…

Q: 3 Determine the eccentric compressive strength, i.e., load and moment, corresponding to (i) balanced…

A: Solution: Note: Minimum shall be designed for i equal to unsupported length of column /500 +…

Q: Steel, fy (main bars) = 415 Mpa Steel, fyt (ties) = 275 Mpa 1. Determine the minimum spacing “a”,…

Q: Current Attempt in Progress Two 4-in.-wide wooden boards are to be joined by splice plates that will…

Q: For the illustrated plain concrete T-beam, compute the stress at top and bottom of the extreme…

Q: 25 A P₁ 45 P2 no to 45 P2 25 P₁ 45 P2 E 6 panels @ 3.0 m = 18.0 m 43 P₂ K 25 P₁ 6.0 m

A: Solution: Here it is a symmetric section and the loadings also symmetrical. Hence it is enough to…

Q: use method of members to get results of joints A to E

A: To find reactions at all points

Q: A short column is made by nailing four 1 x4-in. planks to a 4 x 4-in. timber. Using an allowable…

A: Given: A short column is made by nailing four 1 x4-in. planks to a 4 x 4-in. timber. Using an…

Q: For the beam and loading shown, consider section n-n and determine the shearing stress at (a) Point…

Q: The timber beam is subjected to a shear force of V = 7 kips. 1) Plot the shear stress diagram along…

A: Shear force : Shearing forces are unaligned forces that push one part of a body in one direction and…

Q: STEEL STRUT e BASE PLATE CONNECTOR PLATE ANCHOR BOLT 8.617 mm thick Steel strut is connected to the…

A: This question is related to the Design Steel structures.

Q: P P – L - 6 in. (1) (2) 0.5 in.-

A: Given data: width = 6 in.

Q: c. Using a 0.5pbalanced limit on the reinforcement, determine the required beam dimension (b-width…

A: Dead load, wD = 26 kN/mLive load, wL =20 kN/mLength of the beam, L = 5mReinforced ratio = 0.5 *…

Q: The dimensions of a rectangular beam are limited to b - 300 mm and effective depth, d- 700 mm.…

A: Given data:- Width of rectangular bar, b = 300 mm Effective depth, d = 700 mm f'c=28 MPafy=415 Mpa…

Q: ne column under the effect of compound bending in the direction for the given reinforcement layout,…

A: Question is based on the rectangular column .Dimension of column , details of reinforcement are…

Q: iral column carries a dead load of 1070 kN and a live load of 980 kN. If f’c = 27.50 MPa, fy =…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 1-87. The beam is made from southern pine and is supported by base plates resting on brick work. If…

Q: - Using #3 stirrups and assuming a cross-section with b= 10" and d = 20", for the factored shear…

A: Introduction- A stirrup is a closed loop of reinforcement bars that holds the main reinforcing bars…

Q: Five planks (4@ 40 x 40 mm and 1@ 40 x 380 mm), are joined together to form the l-section shown.…

Q: A reinforced concrete beam has the following properties: Beam width = 320 mm Effective depth = 640…

Q: The beam is made from southern pine and is supported by base plates resting on brick work. (Figure…

A: Given: Required : Length of base plate at A and B

Q: 9. It is a term used for beam sections where under flexural loads, steel reinforcement will yield…

A: Asked: To choose the correct option corresponding to the given statement.Given statement:It is a…

Q: (i) Determine the rivet value of 20 mm diameter rivets connecting 10 mm plate and is in (a) single…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: Problem 6.3 A short column is made by nailing four 1 x 4-in. planks to a 4x4-in. timber. Using an…

A: Given data : Allowable stress = 600 psi To Find : Determine the largest load P that can be applied…

Q: At a cross section in a rectangular beam with b=300 mm and d=500 mm, flexural reinforcement is 5T20.…

A: to calculating load condtion, here beam type is not given, for simplification generally simply…

Q: Please answwer the question in the picture, Show all of your work please.

A: Follow the steps...Image_1Image_2Image_3As calculated above Absolute Maximum SF =17 kipAbsolute…

Q: 2 kN The beam is made of three boards nailed together to form the double-T cross section shown. If…

Q: cover = 40 mm Concrete, f’c = 27 MPa Steel, fy (main bars) = 415 Mpa Steel, fyt (ties) = 275 Mpa 1.…

Q: : The continuous beam shown in figure below ha a positive reinforcement consists of (4#19 bars)…

A: Consider the cross-sectional layout of the beam Calculate the factored load on the beam

Q: Situation 1 | A built-up beam made from fastening two channels to a wide flange section carries…

A: Diagram;Draw SFD;Thus Vmax = 49.077 kn

Q: A 25.6 mm diameter bolt having a diameter at the root of the threads of 21.7mm is used to faster two…

A: Given, Diameter of the bolt, db= 25.6mm Diameter of the thread, dt= 21.7mm Tensile Force, P= 34 kN…

Q: A 16 mm-diameter steel rod AB is fitted to a round hole near end C of the wooden member CD. For the…

Q: Design will be carried out as per provisions of TS 500 1 kb = 1300mm d=560km +250 + Inf =120mm…

Q: For the timber beam and loading shown, determie the safe value of “h" when the allowable bending…

Question

100%

1. built up timber-beam is subjected to a vertical shear of 5 kN. Knowing that the allowable shearing force in each
nail is 300 N, Which nearly gives the largest permissible spacing of the nails in mm.
50 mm
250
50 mm
50 mm 50 mm
50 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need a solution quickly, Use ACI Code
Three steel bolts are to be used to attach the steel plate shown to a wooden beam. The plate will support a 110KN and the ultimate shearing stress for the steel used is 360MPA and that a factor of safety of 3.35 is desired, determine the decrease in the bolt diameter required if the 110kN load is decreased to 90kN. 1OKN
A beam is composed of the following cross-section and carries a maximum shear of 4000lb. Find the force in all four nails assuming a spacing of 1.5”. Show all process steps please
In a slab-floor system with the total depth of 22 in., the flange effective width was determined to be 40 in. The beams have a web width of 14 in. and the slab thickness is 3 in. Design the reinforcement for a typical interior beam if the factored applied moment, Mu is 9500 k-in. f’c = 6ksi and fy = 80 ksi. Draw the detailing.
Problem- What should be the depth of web required as per serviceability criterion if no transverse stiffners are provided and the web is connected to flanges along both longitudinal edges. Take depth of web to be 1900 mm and yield stress of steel to be 250 MPa.
Q3: А- Oesign a rectangular beam with b = 350 mm, h = 625 mm as shown below. Use f! = 30 MPa, fy = 375 MPa and Ø18 mm for %3D fongitudinal reinforcement. Two lavers of tension reinforcement. PE45 kN Wu,-25 kN/m WUT14 kN/m D.L babulb 5 m B- Check the design of the singly reinforced beam shown below, if fc = 20 MPa and fy = 420 MPa, 030 mm for tension. Why? %3D sed edr arlagead iso t 430 mm 100 mm 300 mm
I need correct solution
Design the T beam for the floor system when subjected to an ultimate moment of 300 kN-m. Beam span is 6m, beam width is 300 and d is 450mm. fc = 30 MPa, fy = 420 MPa. Determine the effective width of the T-beam in mm. Is the compressive flange adequate enough to provide the design capacity required? How many layers/rows of steel rebars are expected in the design of reinforcement? How many 25mm steel bars are required for the section?
Please upload with complete drawing and solution. If u can pls add some explanation,thankyou!
3. Three 18 mm diameter steel bolts are to be used to attach the steel plate to a wooden beam. The plate has to support a load of 110 KN. The ultimate shearing stress for the steel used is 360 MPa. Determine what will be the factor of safety for this design. HOAN
please give detail on how to get all value and diagram
Problem 4: Two wooden members shown which support a 4.5kip load, are joined by plywood splices fully glued on the surfaces in contact. The ultimate shearing stress in the glue is 360psi and the clearance between members is 1/4in. Determine the required length L of each splice if a factor of safety of 2.75 is to be achieved. 4.5kips 4 in 4.5kips