A 3m both ends hinged timber column is made of Apitong wood with the following properties: Fc = 9.56 MPa (parallel to grain) Fc = 2.20 MPa (perpendicular to grain) E = 7310 MPa If it has a square section with 200mm side dimension. Compute the actual slenderness ratio of the column. a. 12 b.13 c.14 d.15

A 3m both ends hinged timber column is made of Apitong wood with the following properties: Fc = 9.56 MPa (parallel to grain) Fc = 2.20 MPa (perpendicular to grain) E = 7310 MPa If it has a square section with 200mm side dimension. Compute the actual slenderness ratio of the column. a. 12 b.13 c.14 d.15

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 58. Calculate the nominal axial strength of the column in KN
A steel plate (called a cover plate) having cross-sectional dimensions W2 8.0 in. x 0.7 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 14.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =|
Question 6 of 6 Fill in the blanks: Determine the design moment capacity of the beam with given properties below. bf = 400mm bw = 350mm tf = 120mm d = 370mm d' = 100mm fc' 34.5 MPa fy = 420 MPa As = 8- 28mm bars USE NSCP 2015, Mu = KN-m
For the Beam section below, check if steel yields and determine the ACI design flexural strength. 12 in. 15 in. 4 #10 bars $3 in. f, = 60,000 psi f;= 4000 psi -18 in.-
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Determine the forces in members using the method of section FE, LK, and LG. Include your complete solution along with its free body diagram.
The beam shown has the following properties. f’c= 30 MPa, fc=13.5 MPa, fy=400 MPa, fs=200MPa. c) The cracked section properties Kd and ICR.
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area? The following W Section were considered for the design: W10x33 W14x38 W8x40 W16x36 W10x39 W8x13 189 KN 1.50 HL B 145 KN 1.50 E + 137 KN 121 KN -3.00 + 12.00 3.00 154 KN + W4x13 W6x9 W10x12 200 KN -1.50 1.50 1 030 T 1.20 +2.40 0.60 L i 0.30
A wide flange section has the following properties. A- 6645 mm? bị = 152.40 mm ty - 10.80 mm d- 449.58 mm tw - 7.62 mm Fy - 250 MPa Compute the plastic section modulus about the major principal axis. (x 10° mm)
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 7 m long, pinned at the top fixed at bottom, and has additional support in the weak direction 3 m from the top. Properties of the section are as follows: A = 14,500 mm^2 Ix = 258.6 x 10^6 mm^4 Iy = 84.375 x 10^6 mm^4 1. Calculate the critical slenderness ratio of the member. a. 26.208 b. 45.882 c. 36.706 d. 27.529 2. calculate the nominal axial load capacity of the column a. 3104 kN b. 4851 kN c. 4213 kN d. 5344 kN 3. calculalte the service axial dead load if the service axial live load is twice as that of the dead load. Use LRFD. a. 1354 kN b. 992 kN c. 1093 kN d. 634 kN
A For the truss shown, find veyticat deflection bylunit lead Methed. EA 15 _atfd) Ioku for all members increase in temp is (50€) in (ad) short in (ad)is (3 Emfr
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 55. calculate the critical slenderness ratio with buckling about strong axis.