Structural analysis The timber beam shown below is made up of 4 boards nailed together as shown in the crosssection. Determine the value of shear Vin kN, considering the minimum of strengths at Band C. Use spacing of the nails s=244 mm and the strength of one nail N=6.1 N. Upload thedetailed solutions in the next question OR you may choose to upload ONE SINGLE FILEcovering all solutions at the end.15 mmTSVkNC-60 mm15 mmB60 mm15 mm

Answered: Image /qna-images/answer/23f74f4b-6449-4c9b-93e3-daedf41ff36c.jpg

Answered: The timber beam shown below is made up…

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.3.8P

See similar textbooks

Similar questions

12. Refer to figure 6. The 20-mm-diameter bolt fastens two wooden planks together. The nut is tightened until the tensile stress in the bolt is 150 MPa. Find the smallest safe diameter d of the washers if the working bearing stress for wood is 13 MPa. = 20 mm a. 70.8 mm b. 75.2 mm c. 86.3 mm d. 80.5 mm e. none of the above FIGURE 6
Question j=169" R=2.1" ;f 4- 2.81 d $ 100 08 96 07 h £=0.5" * # >P d=7.3" Material is ASTM A36. Plate is fixed 511 by 4 screws of {"$. using the information provided, calculate the ultimate stress (factored by LRFD) for shear fracture and tensile rupture of block pattern passing through points the shear 3-10-9-4..
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
EQuiz No.3 584nkkz1 Cc7KLzOsdr9YUFgvcfFSqpsdlyljtewQ/formResponse Choose the correct answer What will be the value of load applied parallel to the diagonal of (100x100x100))mm cube since the splitting tensile strength=3 Mpa 57.8 KN O 46.7 KN O 47.1 KN O (28)=27.5 Mpa, then the fc(180)=-- for concrete produced using moist
b) Figure Q1(b) shows a glued connection between 3 metal plates. The plates are 500 mm wide. The glue has a shear capacity of 30 MPa. i. Determine the glue length L if the value P = 80 kN. ii. If the glue is to be replaced by 12 mm diameter bolts with shear strength of 180 MPa, determine the number of bolts required. P. 500mm P/2 P/2 FIGURE Q1(b)
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
(1) Given A992 steel Ag = 10 in %3D KLy- 80, ry what is $ Pa=? = 60 the' column streugth design
Calculate the ultimate moment of the given triangular column cross-section section Mr? Paste your PEG or PNG Proof paper using menu above Na=150 kN 90 mm A = 3024 A2 =024 As2 600mm fot = 17 MPa fya = 365 MPa As1 1 60 mm 600 тm
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
cd efgh ij O klmn u op V 0 0 0 t Р What is the line for which the section will rupture in tension? All holes are the same diameter. m n j h d
Question Eight tensile bars with a diameter of 16mm, equally divided into Fwo layers, are developed, C=50mm Spacing between Stirrups = 150 mm center to Center and spacing be tween longitudinal bars is 80 mm if Atr=230 mm? [leastof Cs& cb], Fy = Fyt = 350 M Pa. use Fé = 25,35 and 45 MPa and assume Atr is Satis fied with ACI & BS, Find length of development vequired. > Subject: Advanced Concvete Design, %3D
Q2. The joint connection shown in Figure Q2 is subjected to a medium term tensile load under service class C24. The joint comprises of six 3mm diameter x 150mm long wire nails. If the characteristic density of the timber is 340kg/m³, determine the load carrying capacity P1 and P2 of the connection and slip per nail P2 P 45 mm thick Figure Q2 75 mm thick P1 P1 P 100 mm thick

SEE MORE QUESTIONS

Recommended textbooks for you

Steel Design (Activate Learning with these NEW ti…

Civil Engineering

ISBN:

9781337094740

Author:

Segui, William T.

Publisher:

Cengage Learning