A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two perpendicular direction. If the loading on the flat roof is estimated to be 1 kN/m2. Determine the reduced live load supported by a typical interior column at the ground floor level in KN.

A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two perpendicular direction. If the loading on the flat roof is estimated to be 1 kN/m2. Determine the reduced live load supported by a typical interior column at the ground floor level in KN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

High School building has two stories having interior columns that are spaced 6.6m apart in two directions. The loading on the flat roof is estimated to be 960N/m2. Live load on the second floor is 2400 N/m2. Compute the total live load supported by the ground floor column (interior column kN)
3. A four-story office building has interior columns spaced 30 ft apart in two perpendicular directions. If the flat-roof live loading is estimated to be 15 lb/ft2 and the floor is made of 150 mm thick reinforced cinder concrete. Determine the total load supported by a typical interior column located at ground level
A two-storey school (use classroom) has interior columns that are spaced in 4.5 meters apart in two perpendicular direction. If the loading on the flat roof is estimated to be 1 kN/m^2. Determine the live load supported by a typical interior column at the ground floor level in KN. (Consider reduced live load where applicable)
Q2) A building wall consists of 12-in. clay brick and in. fiberboard on one side. If the wall is 10 ft high, determine the load in pounds per foot that it exerts on the floor. Q3) A building wall consists of exterior stud walls with brick veneer and 13 mm fiberboard on one side. If the wall is 4 m high, determine the load in kN/m that it exerts on the floor.
QUESTION 4 Design data related to the action and construction material are as follows: for Variable action retail shop= 3.0 kN/m².Floor finishes, ceiling and building services = 1.5 kN/m² and Permanent Load of 4.5 kN/m². Determine the design action including maximum shear force and maximum bending moment for beam 1/A-D in Figure 4 can withstand the new variable action for retail shop. This beam also carries a 3 m high brickwall with a weight of 2.6 kN/m² 2 4500 4500 4000 (09+*092)241 169/250x450) 4500 (OGPROGZ)41 4500 164/250x450) 1 FS1 163/250x450) FS2 1b2(250x450) 1 FS3 1b1(250x450) FLOOR KEY PLAN ALL SLAB THICKNESS-125MM THE UNLO 1b6(250x450) 4500 TOODED J 1b10(250x450)
A two-story office building has interior columns that are spaced at 6.71 m apart in two perpendicular directions. If the loading on the flat roof is estimated to be 0.96 KN/m2, determine the reduced live load supported by a typical interior column at the (a) ground floor level and (b) second floor level Minimum live load for offices is 2.4 KN/m2
1. A three-storey office buiding with roof deck has an interior floor plan shown below. Each columns are spaced 6.7m each way. If the 2nd and 3rd floor levels are dedicated as business processing offices, determine the reduced live load in kPa carried by the interior column highlighted below by the ground floor. H H H H H I AT 6.7m 6.7m H 6.7m I 6.7m I
A three-span continuous one-way slab with clear spans of 3.5 meters and thickness of 125mm is supported on beams 300 mm wide (monolithic construction). Effective depth of the slab is 99mm. The slab carries a floor live load of 2.4 kPa and a superimposed dead load of 1.5kPa. Use f'c = 21 MPa and fy = 275 MPa. Unit weight of concrete 24 kN/m3. For moment calculation, refer to RC-04. Use 2010 NSCP. Considering exterior panel: a. Calculate the maximum negative moment considering a 1 m strip. b. Calculate the maximum positive moment considering a 1 m strip. c. Calculate the spacing of 12mm@ main reinforcing bars for negative bending. d. Calculate the spacing of 12mm@ main reinforcing bars for positive bending. e. Find the spacing of 10mm temperature bars.
A6m cantilever 200x500 rectangular beam is carrying a unformly varying downward load of 0 kN/m at the free end to 184 kN/m at the fixed end. There Is an upward load of 312 kN at the free end. If the allowable flexural stress of the beam is 120 MPa and if the beam is to carry only a uniformly distributed load in kN/m. determine the safest uniform load that it can carry.
The second floor of a light manufacturing building is constructed from a 125 mm thick stone concrete slab with an added 100 mm cinder concrete as shown. If the suspended ceiling of the first floor consists of metal lath and gypsum plaster, determine the dead load for design in kN per square meter of the floor area. 125 mm concrete slab ceiling 100 mm cinder concrete ANS. 5.055 kN/m²
A prestressed concrete beam 100 mm x 300 mm in cross-section is prestressed with a straight cable at an eccentricity of 50 mm below neutral axis. The effective prestressing force is 75 kN. The span of the beam is 5 m and total load on the beam including the self weight is 2.4 kN/m. What is the eccentricity of C-line at the quarter span?