The regular three-storey building has following plan dimensions 20 m* 20 m. Dead load on each floor is 5 kN/m2 and dead load on the roof is 4 kN/m2. The live load on each floor is 3.5 kN/m2 and on roof is 1 kN/m2. Find the total seismic weight.

The regular three-storey building has following plan dimensions 20 m* 20 m. Dead load on each floor is 5 kN/m2 and dead load on the roof is 4 kN/m2. The live load on each floor is 3.5 kN/m2 and on roof is 1 kN/m2. Find the total seismic weight.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A four storey building of 25m × 25m plan dimensions and 3m floor height is located in seismic zone IlI on a site with medium soil. The structure type is special moment resisting frame. Seismic weight of first floor, second floor and third floor; W1 = W2 = Wa = 5000kN. Seismic weight of roof slab, W4 = 3500kN. Calculate design base shear and story shear using seismic coefficient method.
A 4-storey with Roof deck AFP armory is to be constructed in Sulu. The facility is essential for the housing of the Philippine Army's newly purchased weapons, ammunitions and explosives. The location of the facility is 7.5 km from the known source which is capable of producing a magnitude 6.7 earthquake. The structure is a Steel MRF with an overall height of 14m from the NGL. The weight per level of the slabs and stairs is equal to 1740 kN. For the walls at the typical levels, the weight is computed as 2362.5 kN and for the parapet at the roof deck level, the weight is computed as 388.8 kN. An equipment 2.0 meters high with a hexagonal cross - sectional area whose sides equal to 1 meter is installed at the second level and has a weight of 100 kPa. Using R = 8.5, which of the following most nearly gives the lateral force at the 4th level in kN? Use Soil Type A.
Find the short term and long term deflections of the type 1 prestressed concrete beam shown in Fig. 8.3. The beam has a rectangular cross- section of 0.3 m × 0.6 m and a effective span of 16 m. 0.1: +0.2 0.24 0.1 4 8 m fc= 50 N/ mrn? 800' KN. Pe- G50 KN
Please answer correctly
Give me right solution according to the question.
The reinforced concrete beam shown has a width of 400 mm and a total depth of 610 mm. It is loaded with a super imposed dead of 25 kN/m, and live load of 12 kN/m. Pdl =60kN and Pll = 40kN There are 3-25mm diameter bars arranged in a single layer at the bottom of the beam, with a clear covering of 50 mm. Another 2 -20 mm diameter bars are located at the top of the beam with the same clear covering. Determine the critical spacing of 10mm diameter stirrups. Use f = 28MPa, fy = 420 MPa, fyt = 275 MPa. P in KN P in KN w in kN/m Steel I Generic 7.0 m 2.0 m 5.0 m
ABCD is a Raft Foundation rectangular plan with dimension of 20m*12m. The uniformly distributed load over the Raft 400kn/m².find the stress at point "O" which is the middle point of the Raft at the depth of below 6m.
A 6 storey reinforced concrete building, with a floor to floor height of 4.4m is stabilized by shear wall as with a stiffness, Ecdlc, of 326,779,492 kNm² in the transverse direction. Calculate the maximum vertical load, FV,Ed, in KN that can be applied to the building without it becoming sensitive to second order effects in the transverse direction. It can be assumed that the shear walls are cracked.
Question :- The width of the beam is 250 mm and the overall deep 620 mm. It has three equal spans of 6.0 m each. The beam is arranged at 3.5 m from center to center, while the thickness of the slab is 200 mm. The imposed live load qk on the beam is 45 kN/m and the dead load gk inclusive of self-weight of the beam is 75 Kn/m. the characteristic strength of materials are feu = 30N/m², fy = 460N/mm² and f 250N/mm², Assume that the mild exposure for the beam and the nominal cover of 25 mm. Design the beam
The floor shown below with an overall depth of 125 mm is to be designed to carry an imposed load (LL) of 2.5 kN/m² plus floor finishes and ceiling loads (DL) of 1.5 kN/m². Calculate the factored loads acting on beams CD. Assume unit weight of concrete is 24 kN/m². E 2. F 3.0 m 5.0 m Depth 125mn 0.125m -hh=2.5 kN/m² - PL = 1.5 kNm² - u. W of compete 24 KN/m³ A 80m B
Compute the maximum combined loads using the recommended ASDexpressions from the AISC. D = 10,000 lb,W = ;32,000 lb
A 250mm x 600mm 10m-simple span prestressed concrete beam has a uniformly distributed dead load of 8.50 kN/m in addition to its weight. The tendons are placed 100mm from the bottom of the beam and is subjected to initial prestress force of 1880 kN. The beam is used to carry a live load of 25 kN/m. If the unit weight of concrete is 24 kN/m3, determine the stress at the bottom fiber of the beam at midpan after 20% of the losses at its final stage CS Scanned with CamScanner