Given the floor layout below. Assume this is an upper story in a multistory office building. Perform live load reduction as appropriate. The floor is subjected to service (i.e. unfactored) superimposed dead load of 6.94 kPa and L = 3.24 kPa. Concrete weighs 23.6 kN/m3. Typical interior floor beam is 326 x 649 mm. Slab thickness is 143 mm. Columns are 352x352 mm square. Determine the maximum factored bending moment (in kN-m) on a typical interior floor beam (secondary) assuming simply supported at both ends. 1 9-75 m 9-75 m 3 9-75 m 4 2 @ 6m 2 @ 6 m 2 @ 6m 2 @ 6 m 12 m 12 m 12 m 12 m

Given the floor layout below. Assume this is an upper story in a multistory office building. Perform live load reduction as appropriate. The floor is subjected to service (i.e. unfactored) superimposed dead load of 6.94 kPa and L = 3.24 kPa. Concrete weighs 23.6 kN/m3. Typical interior floor beam is 326 x 649 mm. Slab thickness is 143 mm. Columns are 352x352 mm square. Determine the maximum factored bending moment (in kN-m) on a typical interior floor beam (secondary) assuming simply supported at both ends. 1 9-75 m 9-75 m 3 9-75 m 4 2 @ 6m 2 @ 6 m 2 @ 6m 2 @ 6 m 12 m 12 m 12 m 12 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. An interior reinforced concrete slab has to be designed to support a live load and a dead load in addition to its own weight based on the following specifications: The slab is one-way and simply supported with a span of 12 ft. The live load on the slab is 200 psf. The dead load on the slab is 100 psf. Your design will use concrete compressive strength fe= 3000 psi and steel yield strength of fy = 40,000 psi
A slab panel is carrying a superimposed dead load of 2.70 kPa and superimposed live load of 6.0 kPa all over the 4.0 m x 18 m light storage area. The slab is restrained. The concrete to be used has strength of 28 MPa (normal weight). The main reinforcement has yield strength of 350 MPa. Use concrete cover of 20 mm. The thickness uses a multiple of 10 mm. The main reinforcement used is 16 mm in diameter The shrinkage and temperature reinforcement used is 12 mm in diameter The unit weight of concrete is 23.6 kN per cubic meter. Using USD, Determine the spacing of 12 mm main rebar at the support.
1. Simply supported beam, 6 in by 12 in, fb = 600 psi, find center load P =? (Include self-weight, assume 150 pcf concrete)
ll中国移动 4G PN © 11:50 PM 75% 4 A spiral column with the diameter of 500 mm has the effective height of lo-4.0 m. The axial compressive strength of the concrete is f. - 14.3 N/ mm. The longitudinal steel bars are 6 22 with the yield strength ofS, - 360 N/mm. The spirals are 10@50 with the yield strength of f,- 270 N/ mm². If the concrete cover is 30 mm thick, determine the ultimate compressive capacity of the column.
Based on Eurocode 2 (2004), the flexural capacity of the section shown below Is 60 kN.m for the concrete cylinder strength (fem) of 40 MPa. Estimate the flexural capacity of the section if the concrete cylinder strength (fcm) becomes 30 MPa. 150 mm Lever arm (z) = 180 mm
CAN SOMEONE HELP ME SOLVE THIS REINFORCED/PRESTRESSED CONCRETE PROBLEM. USE NSCP 2015 A concrete beam has a width of 304.8 mm and an effective depth of 495.3 mm. It is reinforced with 14.194 cm2 steel bars with fc′ = 17,237.5 kPa (n = 10). Determine the flexural stresses caused by a bending moment of 84.1 kN·m
A singly reinforced rectangular beam 350 mm wide and 450 mm deep is reinforced with 2-16-mm-diameter bottom bars enclosed with 10-mm-dia stirrups covered with 40 mm of concrete.Calculate the tensile steel strain compatible with concrete strain of 0.003. Use f'c = 26 MPa and fy = 370MPa. Express your answer in 4 decimal places
Q.1\ A column of a cross-section (350x450)mm is reinforced with 4 bars of (25mm) in diam., knowing that Es=200,000MPa and Ec 22,500MPa and f28MPa and fy = 420 MPa determine the following: 1. The axial load that will stress the concrete to 10 MPa. 2. The normal axial compression strength.
Kindly write the COMPLETE solution NEATLY. Thank you
For the beam and loads shown, select stirrup spacings if f'e = 4000psi, normal-weight concrete and for = 60,000 psi. The beam weight is already included in the given dead load. Assume #4 stirrups. WL = 2 k/ft 24 in. 27 in. 28 ft -16 in. 3 in.