An important building is in earthquake zone V in India. The seismic weight of the building is 10000 kN and it is designed by ductility considerations. The spectral acceleration factor for this structure is 2.5. The base shear for this structure is

An important building is in earthquake zone V in India. The seismic weight of the building is 10000 kN and it is designed by ductility considerations. The spectral acceleration factor for this structure is 2.5. The base shear for this structure is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A bridge is designed using a prestressed beam as shown. A beam with width b = 250 mm and %3D depth d…

A: Given data Initial Prestress force = 600 KN Width of section b = 250 mm Depth h = 450 mm Loss of…

Q: A cantilever beam, 70 mm wide by 280 mm high and 7 m long, carries a load that varies uniformly from…

Q: A concrete beam of rectangular cross-section of size 120 mm x 200 mm is prestressed by a straight…

A: prestressed concrete : The term "prestressed concrete" refers to a type of concrete that is utilized…

Q: The horizontal stress at the centroid of a PSC beam of a rectangular section 130 mm × 250 mm is 7.5…

A: Given data in question PSC beamCross section 130×250 mmStress 7.5 N/mm2Shear force 70 kNTo find out…

Q: A 450 mm diameter concrete post is reinforced with six steel bars, each with 1 28.mm diameter

A: Given That P = 2000 kN ds = 28 mmdc = 450 mm Ec = 25 GPa Es = 200 GPa FBD of the above figure is…

Q: Concrete compressive strength fe = 40 MPa Concrete tensile strength f = 4 MPa

A: First we wil compute the moment of inertia of the section hence the moment of inertia is I =…

Q: A rectangular concrete beam 250 mm wide and 600 mm deep is pre-stressed by means of 16 high tensile…

A: GIVEN, A rectangular concrete beam of width=250mmDepth=600mmDiameter of wire=7mmEffective…

Q: An aluminum alloy pipe with an outside diameter of 3.4 in. and a wall thickness of 6/16 in.…

A: Given data Outer diameter=3.4 in wall thickness=6/16 in Length=L=13 ft WA=12 lb/ft WB=18 lb/ft…

Q: Find the total deformation for the bar shown in fig. if the axial loads are applied if cross section…

Q: () Mass center and stiffness center of a structure is always the same. ( ) During a moderate…

Q: Beam AZ, 2 in wide by 4 in high, is subjected to a loading condition as shown. Determine (a) the…

Q: An 2014 T-6 aluminium flag pole with a hollow rectangular section experiences a wind force of 750 N…

A: ultimate tensile strength : A tensile test is commonly used to determine ultimate tensile strength,…

Q: A cantilever beam, 100 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly…

A: A loaded cantilever beam and it’s cross section is given and it has been asked to determine flexural…

Q: 30 in. 5 in. Knowing that the bending moment in the reinforced concrete beam shown is 150 kip.ft and…

Q: A hollow steel shaft has outside diameter d and inside diameter d/2. The value of d for the shaft,…

Q: machine supporting structure consists of a hollow pipe of external diameter200 mm and wall thickness…

Q: A cantilever beam, 70 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from…

Q: An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 5/16 in.…

Q: A cantilever beam, 70 mm wide by 260 mm high and 8 m long, carries a load that varies uniformly from…

Q: A cantilever beam, 80 mm wide by 280 mm high and 8 m long, carries a load that varies uniformly from…

Q: Determine the maximum uniform distributed load wo that can be supported by the reinforced concrete…

A: The given data is: σall(st)=28 Ksiσall(con)=3 Ksib=10 md=20-2.5=17.5 mAs=2×π4(0.75)2=0.88…

Q: If the maximum load carried by a 6" concrete cylinder specimen is 60 kips, what is the compressive…

A: Here, multiple questions are asked and as per the guidelines only very first question will be…

Q: Current Attempt in Progress The extruded plastic shape has dimensions of D-40 mm, d-34 mm, a-81 mm,…

A: Given data:- D= 40 mm d = 34mm a=81mm t= 8mm V= 360N Allowable shear stress =1100kpa

Q: long is subjected to à čôncentrated simply supported beam, 2 in Wide by 4 in high and 12 load of…

A: Length=12 ftWidth=b=2 inDepth=d=4 inMoment of inertia= bd312=2×4312=10.67 in4B.M is max. under the…

Q: A reinforced concrete beam is subjected to the following bending moments. Moment due to dead load =…

Q: The pipe is subjected to a wind loading that increases from WA= 12 lb/ft at its base to wg = 18 | a)…

A: The given data is: Outside diameter, D=4.8 in Wall thickness, t=3/16 in Calculating the inside…

Q: A simply supported beam, 2 in wide by 7 in high and 15 ft long is subjected to a concentrated load…

A: Given a simply supported beam subjected to a concentrated load of 2000lb at a point 3 ft from one…

Q: An aluminum alloy pipe with an outside diameter of 5.2 in. and a wall thickness of 6/16 in.…

Q: important building ne V in India. The ilding is 10000 kN ctility considerations. ctor for this…

Q: A concrete beam is post-tensioned by a cable carrying an initial stress of 1000 N/mm2. The slip at…

A: Given- Initial stress=1000 N/mm2, Slip=5 mm, E=210 kN/mm2, Length of beam=30 m.

Q: A cantilever beam, 80 mm wide by 260 mm high and 7 m long, carries a load that varies uniformly from…

Q: Calculate the stiffness reduction factor (τa) for an axial compressive stress of 25 ksi and Fy = 50…

A: From AISC manual the stiffness reduction factor can be found out as shown below:

Q: In the design of beams for the limit state of collapse in flexure as per IS: 456-2000, let the…

Q: A round vertical steel column 500 mm in outside diameter and a wall thickness of 10mm is reinforced…

Q: A cantilever beam, 80 mm wide by 220O mm high and 9 m long, carries a load that varies uniformly…

Q: A large spherical tank contains gas at a pressure of 430 psi. The tank is 41 ft in diameter and is…

Q: A bar having a cross-sectional area of 700 mm² is subjected to axial loads at the positions…

Q: In the design of beams for the limit state of collapse in flexure as per IS: 456-2000, let the…

Q: The floor of a classroom is made of 150mm thick lightweight concrete. If the floor slab having a…

A: Dead load: Dead load is caused by the self weight of concrete, tiles, plaster, brickwork, etc Live…

Concept explainers

Steel Framing

A steel frame consists of a skeleton frame structure comprising of horizontal I-beams and vertical steel columns fitted in a rectangular grid building construction to brace the floors, walls, and the roof of the building held onto the frame. Due to the implementation of this methodology, the construction of the skyscrapers was feasible.

Question

An important building is in earthquake
zone V in India. The seismic weight
of the building is 10000 kN and it is
designed by ductility considerations.
The spectral acceleration factor for this
structure is 2.5. The base shear for this
structure is

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 150 mm clay reinforced masonry wall of vertical cell units has an effective high tensile steel area in tension of 0.000464 square meters, and a 28-day compressive strength of 8 MPa. In the space below, calculate the wall's rectangular compressive stress block depth. В I U X2 x2
An-Isotropically reinforced slab-supported as shown in the following Fig. carrying a single concentrated load (P). Determine the maximum force (P) which cause the collapse (neglect slab weight), fe' =30MPa, fy 350MPa. Solution methods Yield line theory 15cm 3cm $10@25cm 4m Free 3m Free 12@20cm bent up 75% 3m 3m
Please answer quickly
The floor of a classroom is made of 150-mm thick lightweight concrete. If the floor is a slab having a length of 8m and width of 6m, determine the resultant force (in KN) caused by the dead load, the live load, and the total load. Note: lightweight concrete is 0.015KN/m2 per mm thickness & classroom is 1.92KN/m2
An aluminum alloy pipe with an outside diameter of 4.9 in. and a wall thickness of 2/16 in. cantilevers upward a distance of L = 20 ft. The pipe is subjected to a wind loading that increases from WA = 8 lb/ft at its base to WB =12 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
A concrete beam of rectangular cross-section of size 120 mm (width) and 200 mm (depth) is pre-stressed by a straight tendon to an effective force of 150 kN at an eccentricity of 20 mm (below the centroidal axis in the depth direction). The stresses at the top and bottom fibres of the section are
A cantilever beam, 100 mm wide by 240 mm high and 8 m long, carries a load that varies uniformly from zero at the free end to 1400 N/m at the wall. Compute the magnitude of the maximum flexural stress. Answer must be in MPa.
Which of the following statements is true for regular, isotropic beams: Maximum bending or flexural stress occurs at the neutral axis. Flexural stress varies linearly along the cross-section of the beam. Maximum horizontal shearing stress occurs at the neutral axis. Horizontal shearing stress varies "parabolically" along the cross-section of the beam. Maximum bending or flexural stress occurs at the point in a cross-section that is furthest from the neutral axis. Flexural stress varies linearly along the cross-section of the beam. Maximum horizontal shearing stress occurs at the point in a cross-section that is furthest from the neutral axis. Horizontal shearing stress varies linearly along the cross-section of the beam. Maximum bending or flexural stress occurs at the point in a cross-section that is furthest from the neutral axis. Flexural stress varies linearly along the cross-section of the beam. Maximum horizontal shearing stress occurs at the neutral axis. Horizontal shearing…
An aluminum alloy pipe with an outside diameter of 5.7 in. and a wall thickness of 5/16 in. cantilevers upward a distance of L = 12 ft. The pipe is subjected to a wind loading that increases from wA = 7 lb/ft at its base to wB = 11 lb/ft at its tip. (a) Compute the maximum value of Q for the pipe. (b) What is the maximum vertical shear stress in the pipe?
An aluminum alloy pipe with an outside diameter of 5.0 in. and a wall thickness of 3/16 in. cantilevers upward a distance of L = 17 ft. The pipe is subjected to a wind loading that increases from wA = 13 lb/ft at its base to wB = 20 lb/ft at its tip.(a) Compute the maximum value of Q for the pipe.(b) What is the maximum vertical shear stress in the pipe?
At the limit state of collapse, an RC beam is subjected to flexural moment 200 kNm, shear force 20 kN and torque 9 kNm. The beam is 300 mm wide and has a gross depth of 425 mm, with an effective cover of 25 mm. The equivalent nominal shear stress (t) as calculated by using the design code turns out to be more than the design shear strength (T) of concrete, The equivalent shear force and equialent flexural moment ?
Quick answer.