A steel pipe of 12-in. outer diameter is fabricated from 1/4-in.-thick plate by welding along a helix that forms an angle of 45° with a plane parallel to the axis of the pipe. Knowing that the maximum allowable tensile stress in the weld is 9 ksl, determine the largest torque that can be applied to the pipe. 12 in. +in. The largest torque that can be applied to the pipe is [ kip-in.

A steel pipe of 12-in. outer diameter is fabricated from 1/4-in.-thick plate by welding along a helix that forms an angle of 45° with a plane parallel to the axis of the pipe. Knowing that the maximum allowable tensile stress in the weld is 9 ksl, determine the largest torque that can be applied to the pipe. 12 in. +in. The largest torque that can be applied to the pipe is [ kip-in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall thickness. Knowing that the maximum stress after the offset is introduced must not exceed 4 times the stress in the tube when it was straight, determine the largest offset that can be used.
Link BD consists of a single wooden member 38 mm wide and 19.2 mm thick. Knowing that each pin has a 14.3-mm diameter, determine the maximum value of the average normal stress (in MPa) in link BD if θ= 0° and P = 26.7. Round off the final answer to three decimal places.
V3
Two horizontal 14.52-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.63-in. diameter is used at each connection, determine the bearing stress (in psi) at A in member AB. Round off the final answer to two decimal places.
84 two decimal places
In the hanger shown the upper portion of link ABC is 9-mm thick and the lower portions are each 6-mm thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 9-mm diameter while a 6-mm-diameter pin is used at C. Determine (a) the shearing stress in pin A. (b) the shearing stress in pin C, (c) the largest normal stress in link ABC, (d) the average shearing stress on the bonded surfaces at B, (e) the bearing stress in the link at C. 30 mm 150 mm 40 mm 170 mm 240 mm 2400 N 120 m
Fig. 3. 4. Determine the efficiency of the riveted butt joint with 20 mm main plate, 12 mm cover plates and 25 mm alloy steel rivets as shown in Fig. 4. Take allowable stress in shear for the rivets as 82.7 MPa, tensile strength of the plates as 144.8 MPa and allowable bearing stress as 89.6 MPa. ø 25 mm rivets 150 mm 12 mm 20 mm Fig. 4.
A steel pipe of 400-mm outer diameter is fabricated from 10-mm-thick plate by welding along a helix that forms an angle of 20°with a plane perpendicular to the axis of the pipe. Knowing that the maximum allowable normal and shearing stresses in the directions respectively normal and tangential to the weld are σ = 60 MPa and τ = 36 MPa, determine the magnitude P of the largest axial force that can be applied to the pipe.
I need the solution for this problem. Under normal operating conditions, the electric motor exerts a torque at point E of 12 kip-in. Knowing that each axis is solid, determine the maximum shear stress on (a) axis BC, (b) axis CD, (c) axis DE.
Two horizontal 12.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 0.8-in. diameter is used at each connection, determine the bearing stress (in psi) at Bin member BC. Round off the final answer to two decimal places.
solve leteer e
An axial centric force of magnitude P = 300 kN is applied to the composite block shown by means of a rigid end plate. Knowing that h = 10 mm, determine the normal stress in (a) the brass core, (b) the aluminum plates. Use units [N,mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer!