In the hanger shown the upper portion of link ABC is 9-mm thick and the lower portions are each 6-mm thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 9-mm diameter while a 6-mm-diameter pin is used at C. Determine (a) the shearing stress in pin A. (b) the shearing stress in pin C. (e) the largest normal stress in link ABC, (d) the average shearing stress on the bonded surfaces at B, (e) the bearing stress in the link at C. 30 mm 150 mm 40 mm 170 mm 240 mm 2400 N 120 m

In the hanger shown the upper portion of link ABC is 9-mm thick and the lower portions are each 6-mm thick. Epoxy resin is used to bond the upper and lower portions together at B. The pin at A is of 9-mm diameter while a 6-mm-diameter pin is used at C. Determine (a) the shearing stress in pin A. (b) the shearing stress in pin C. (e) the largest normal stress in link ABC, (d) the average shearing stress on the bonded surfaces at B, (e) the bearing stress in the link at C. 30 mm 150 mm 40 mm 170 mm 240 mm 2400 N 120 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM NO. 2 For the frame shown, a 4998-N load is acting on member ABD at D. If the allowable material shear stress for is 49 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C. 4998-N 1.00 m 1.59 m 45° 0 O B A 1.59 m 1.58 m
A 50-kN force is subjected to a lap joint fastened by three 20-mm diameter rivets. (a) the shearing stress in each rivet. (b) the bearing stress in each plate. (c) the maximum average tensile stress in each plate. Assume that the axial load P is distributed equally among the three rivels. equally among the three rivels. To o o P 20 mm -25 mm P.
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed
3. A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross- sectional area of 150 mm x 310 mm to the median line of the cross-section. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube . If it is subjected to a torque T = 15 kN-m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa. Thickness of the tube is 10 mm and the torque T = 15 kN-m.
QUESTION 2 Consider that x = 2.76 ft and y = 7.01 ft. B The 5.7-in diameter steel shaft AB is attached into the rigid wall at C and supported by a smooth bearing at A. The lever AC is welded to the end of the shaft. The maximum allowable stress for shaft AB is 355 psi. Determine the maximum allowable force P in lbs. C
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
Link AC is made of a steel with a 65-ksi ultimate normal stress and has a xin. uniform rectangular cross section. It is connected to a support at A and to member BCD at C by-in.-diameter pins, while member BCD is connected to its support at B by a -in.-diameter pin. All of the pins are made of a steel with a 25-ksi ultimate shearing stress and are in single shear. Knowing that a factor of safety of 3.75 is desired, determine the largest load P that can be applied at D. Note that link AC is not reinforced around the pin holes. 16 IN 8 in 16. ---4 in- The largest load P that can be applied at Dis[ lb.
2. A 6 mm diameter pin is used in connection C of the pedal shown. Knowing that P = 500 N. Determine: 1. The average shear stress in the pin. 2. The average crushing effort in the pedal C. 3. The crushing stress in the supports of C. The figure is in the attached image
Problem #1: The following bar has a diameter of 40 mm and is subjected to the loads shown. For the point A determined: 45 N.m 300 mm 5 kN 200 mm B a. The combination of normal and shear stresses b. The maximums and minimums. Indicate the orientation of the principal axes. C. The maximum shear stress. Indicate the orientation of the axes for this effort.
I need answer within 20 minutes please please with my best wishes
Please try to answer the question within 25 minutes here value of R is 48
5. Three wood boards, each 3.5 in. wide, are joined by the 3/4-in.-diameter bolt. If the working stresses for wood are 750 psi in tension and 1450 psi in bearing, find the largest allowable value of the force P. ² 1 in. P 2 in. P 1 in. T in.